HP Designjet 2000/3000cp HP DesignJet 2500/2000CP Printer - User's Guide - Page 297

Replace Ink System, Pause, Message, Explanation and Action, the message Printhead failure

Page 297 highlights

Front-Panel Messages Message Explanations and Actions Message Explanation and Action STATUS Initializing The printer is doing an internal check on power-up. Wait until the printer has finished initializing. STATUS Ink drying (xx m xxs) The ink on your print is drying. Wait before removing the print. If you remove it before the indicated time has passed, avoid smearing the ink. STATUS Lens maintenance STATUS Loading roll The lens cover on the printhead carriage requires maintenance. Press the Replace Ink System key to replace the lens cover with a new one. Spare lens covers are inside the right door. See the instructions for lens cover replacement on page 10-3, Lens Maintenance. The printer is loading roll media. Wait for the loading to complete. STATUS Loading sheet The printer is loading sheet media. Wait for the loading to complete. STATUS Low on ink STATUS Maintenance advised One or more of the four ink systems are out of ink. Press the Replace Ink System key to replace the ink systems affected, if the last print showed any degradation in image print quality. If there is still a large amount of ink remaining in the ink cartridges, see the message Printhead failure on page 12-12. The printer is being used more intensively than the recommended duty cycle. You should contact your local HP dealer or HP service engineer to arrange a service. If you choose to ignore the message, you may continue to use the printer as normal, but may encounter a number of operational or print-quality problems. STATUS Measuring pattern STATUS Out of media STATUS Pause pending The printer is measuring the accuracy calibration print that you just loaded. Wait for the calibration to complete. The printer has received a file, is ready to print, but has no media loaded. Load appropriate media. You have pressed the Pause key but the printer was busy performing a previous action. The printer will pause when it has completed its current action. Wait for the current action to complete. 12-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340

Front-Panel Messages
Message Explanations and Actions
12-19
STATUS
Initializing
The printer is doing an internal check on power-up.
Wait until the printer has finished initializing.
STATUS
Ink drying (xx m xxs)
The ink on your print is drying.
Wait before removing the print. If you remove it before the indicated time has passed,
avoid smearing the ink.
STATUS
Lens maintenance
The lens cover on the printhead carriage requires maintenance.
Press the
Replace Ink System
key to replace the lens cover with a new one. Spare
lens covers are inside the right door. See the instructions for lens cover replacement
on page 10-3, Lens Maintenance.
STATUS
Loading roll
The printer is loading roll media.
Wait for the loading to complete.
STATUS
Loading sheet
The printer is loading sheet media.
Wait for the loading to complete.
STATUS
Low on ink
One or more of the four ink systems are out of ink.
Press the
Replace Ink System
key to replace the ink systems affected, if the last
print showed any degradation in image print quality. If there is still a large amount
of ink remaining in the ink cartridges, see
the message Printhead failure on page
12-12
.
STATUS
Maintenance advised
The printer is being used more intensively than the recommended duty cycle.
You should contact your local HP dealer or HP service engineer to arrange a
service. If you choose to ignore the message, you may continue to use the printer as
normal, but may encounter a number of operational or print-quality problems.
STATUS
Measuring pattern
The printer is measuring the accuracy calibration print that you just loaded.
Wait for the calibration to complete.
STATUS
Out of media
The printer has received a file, is ready to print, but has no media loaded.
Load appropriate media.
STATUS
Pause pending
You have pressed the
Pause
key but the printer was busy performing a previous
action. The printer will pause when it has completed its current action.
Wait for the current action to complete.
Message
Explanation and Action