HP Pavilion Elite e9100 Getting Started - Page 15

Connecting the TV signal source coaxial cable no set-top box, Computer coaxial TV In connector

Page 15 highlights

Connecting the TV signal source coaxial cable (no set-top box) To connect the computer into an existing setup for the TV signal source without a set-top box, insert (add) a splitter (B) to route the coaxial TV signal cable from the wall outlet (A) to the computer connector (C). Callouts A TV signal cable (coaxial) wall outlet (from antenna or cable) B Splitter C Computer coaxial TV In connector D Video recorder E TV F Set-top box/satellite box G Remote control IR blaster cable (select models only) H Computer S-video In connector J Computer right and left audio (analog) connectors Connecting the TV signal source with a set-top box To connect the computer into an existing setup for the TV signal source with a set-top box (cable or satellite), insert (add) a splitter (B) to route the coaxial TV signal cable from the set-top box (F) to the computer connector (C). Connect the remote control cable/IR blaster (select models only) (G) to the IR OUT connector on the computer, and then position the blaster on the set-top box. This enables the computer to change the channel on the box. See "Using an infrared receiver (IR) blaster" on page 13 for blaster placement details. Setting Up Your Computer 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76

Setting Up Your Computer
11
Connecting the TV signal source coaxial cable (no set-top box)
To connect the computer into an existing setup
for the TV signal source without a set-top box,
insert (add) a splitter (
B
) to route the coaxial TV
signal cable from the wall outlet (
A
) to the
computer connector (
C
).
Callouts
A
TV signal cable (coaxial) wall outlet (from
antenna or cable)
B
Splitter
C
Computer coaxial TV In connector
D
Video recorder
E
TV
F
Set-top box/satellite box
G
Remote control IR blaster cable (select
models only)
H
Computer S-video In connector
J
Computer right and left audio (analog)
connectors
Connecting the TV signal source with a set-top box
To connect the computer into an existing setup
for the TV signal source with a set-top box
(cable or satellite), insert (add) a splitter (
B
) to
route the coaxial TV signal cable from the
set-top box (
F
) to the computer connector (
C
).
Connect the remote control cable/IR blaster
(select models only) (
G
) to the IR OUT
connector on the computer, and then position
the blaster on the set-top box. This enables the
computer to change the channel on the box.
See “Using an infrared receiver (IR) blaster”
on page 13 for blaster placement details.