HP StorageWorks 2/16V Brocade Fabric OS Documentation Addendum - Supporting Fa - Page 56

fciptunnel, params, ipsec, iproute, iscsi, Retransmit time, Keepalive Timeout, Maximum Retransmissions

Get HP StorageWorks 2/16V - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/16V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

1 portshow Note: Enter commands in lowercase only; mixed case is for readability Note The execution of this command is subject to Admin Domain restrictions that may be in place. Operands This command has the following operands: arp Displays ARP table. Use this operand to display IP addresses, corresponding MAC addresses, and flags. fciptunnel Displays FCIP tunnel IDs, remote and local IP addresses, remote and local WWNs, compression status, FCIP fastwrite state for the tunnel endpoint, Tape Pipelining status, Uncommitted bandwidth rate, SACK status, Minimum Retransmit time, Keepalive Timeout, Maximum Retransmissions, tunnel status, tunnel uptime. You must specify all to display all FCIP tunnels or tunnel_id to display the specified FCIP tunnel. Additional options include: -perf Displays additional performance information. -params Displays connection parameter information. -ipsec Displays IKE and IPSec policy information on IPSec-enabled tunnels. ipif Displays the IP interface, IP address, netmask, and MTU. iproute Displays the IP address, mask, gateway, metrics, and flags. iscsi Displays GbE port WWN and iSCSI Sessions. mode Displays the mode of the GbE port. slot For bladed systems only, specify the slot number of the port to be configured, followed by a slash (/). [ge]port Specify the port number to be displayed, relative to its slot for bladed systems. See switchShow for a list of valid ports. 1-42 Fabric OS Documentation Addendum Publication Number: 53-1000429-01-HP

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
1-42
Fabric OS Documentation Addendum
Publication Number: 53-1000429-01-HP
portshow
Note: Enter commands in lowercase only; mixed case is for readability
1
Note
The execution of this command is subject to Admin Domain restrictions that may be in place.
Operands
This command has the following operands:
arp
Displays ARP table. Use this operand to display IP addresses, corresponding
MAC addresses, and flags.
fciptunnel
Displays FCIP tunnel IDs, remote and local IP addresses, remote and local
WWNs, compression status, FCIP fastwrite state for the tunnel endpoint, Tape
Pipelining status, Uncommitted bandwidth rate, SACK status, Minimum
Retransmit time, Keepalive Timeout, Maximum Retransmissions, tunnel status,
tunnel uptime. You must specify
all
to display all FCIP tunnels or
tunnel_id
to
display the specified FCIP tunnel. Additional options include:
-perf
Displays additional performance information.
-params
Displays connection parameter information.
-ipsec
Displays IKE and IPSec policy information on IPSec-enabled tunnels.
ipif
Displays the IP interface, IP address, netmask, and MTU.
iproute
Displays the IP address, mask, gateway, metrics, and flags.
iscsi
Displays GbE port WWN and iSCSI Sessions.
mode
Displays the mode of the GbE port.
slot
For bladed systems only, specify the slot number of the port to be configured,
followed by a slash (/).
[
ge
]
port
Specify the port number to be displayed, relative to its slot for bladed systems. See
switchShow
for a list of valid ports.