HP StorageWorks 2/16V Brocade Fabric OS Documentation Addendum - Supporting Fa - Page 76

Updates to the Introduction New AG System Messages, AG-1001, Introduction

Get HP StorageWorks 2/16V - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/16V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

2 Updates to the Introduction Chapter Updates to the Introduction Chapter Add the following row to the System Modules Descriptions tabe on page 1-15. AG Access Gateway mode messages of the Fabric OS. New Chapter, AG System Messages Add a new chapter titled AG System Messages after the Introduction and before the AUTH System Messages; it contains all the new messages for the feature, Brocade Access Gateway mode. AG-1001 Message , [AG-1001], ,, ERROR, , N_Port is connected to a fabric port that does not support NPIV Probable Cause Recommended Action Severity Indicates that the fabric port to which Access Gateway is connected does not support NPIV. Enable NPIV on the port connected to the Access Gateway using the portCfgNpivPort command on the fabric switch. Refer Fabric OS Command Reference Manual for more information on this command. ERROR AG-1002 Message , [AG-1002], ,, WARNING, , Unable to find alternate N_Port during fail over for N_Port Probable Cause Recommended Action Severity Indicates that the F_Ports could not be failed over because no other N_Ports are configured or that the fabric was unstable during the failover attempt. Verify whether or not other N_Ports are configured. If the message persists, run supportFtp to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. WARNING 2-2 Fabric OS Documentation Addendum Publication Number: 53-1000429-01-HP

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
2-2
Fabric OS Documentation Addendum
Publication Number: 53-1000429-01-HP
Updates to the Introduction Chapter
2
Updates to the
Introduction
Chapter
Add the following row to the System Modules Descriptions tabe on page 1-15.
New Chapter, AG System Messages
Add a new chapter titled AG System Messages after the Introduction and before the AUTH System
Messages; it contains all the new messages for the feature, Brocade Access Gateway mode.
AG-1001
Message
Probable
Cause
Indicates that the fabric port to which Access Gateway is connected does not support NPIV.
Recommended
Action
Enable NPIV on the port connected to the Access Gateway using the
portCfgNpivPort
command on
the fabric switch. Refer
Fabric OS Command Reference Manual
for more information on this
command.
Severity
ERROR
AG-1002
Message
Probable
Cause
Indicates that the F_Ports could not be failed over because no other N_Ports are configured or that the
fabric was unstable during the failover attempt.
Recommended
Action
Verify whether or not other N_Ports are configured.
If the message persists, run
supportFtp
to set up automatic FTP transfers; then run the
supportSave
command and contact your switch service provider.
Severity
WARNING
AG
Access Gateway mode messages of the Fabric OS.
<timestamp>, [AG-1001], <sequence-number>,, ERROR, <system-name>,
N_Port <port>
is connected to a fabric port that does not support NPIV
<timestamp>, [AG-1002], <sequence-number>,, WARNING, <system-name>,
Unable to find alternate N_Port during fail over for N_Port
<port
>