HP Surestore Tape Library Model 2/28 HP DLT Tape Library 28/48-Slot - User& - Page 35

Table 2-4, SCSI Interface Mode Switch Settings, Do not use a physical terminator., Setting, Purpose

Get HP Surestore Tape Library Model 2/28 PDF manuals and user guides View all HP Surestore Tape Library Model 2/28 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Table 2-4 CAUTION Library Installation Step 4: Connect the Library to the Host 5. For each bus, set the SCSI interface mode switch as follows. SCSI Interface Mode Switch Settings Setting Term Pwr Termination Purpose Set to Sends termination ON power to the bus Terminates the SCSI bus; functions the same as a physical terminator ON if one port on the bus is open OFF if both ports on the bus are connected to a cable Do not use a physical terminator. If a physical terminator is attached and termination is set to ON, the bus will be overterminated, which could cause the device to function incorrectly. Library Installation 2-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
2-7
Library Installation
Step 4: Connect the Library to the Host
Library Installation
5.
For each bus, set the SCSI interface mode switch as follows.
Table 2-4
SCSI Interface Mode Switch Settings
CAUTION
Do not use a physical terminator.
If a physical terminator is attached and
termination is set to ON, the bus will be overterminated, which could cause
the device to function incorrectly.
Setting
Purpose
Set to
Term Pwr
Sends termination
power to the bus
ON
Termination
Terminates the SCSI
bus; functions the same
as a physical
terminator
ON if one port on the bus is
open
OFF if both ports on the bus
are connected to a cable