Icom IC-M804 Instruction Manual - Page 13

PREPARATION, Entering the MMSI code

Get Icom IC-M804 PDF manuals and user guides View all Icom IC-M804 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

3 PREPARATION ■ Entering the MMSI code The Maritime Mobile Service Identity (MMSI: DSC self ID) code consists of 9 digits. You can only enter the code when turning ON the transceiver for the first time. 2 This initial code can be entered only once. After entering, it can be changed only by your dealer 3 or distributor. If your MMSI code has already been entered, doing the steps below is not necessary. 1. Hold down [ ] to turn ON the transceiver. • Three short beeps sound, and then "Push [ENT] to Register your MMSI" is displayed. 6. Enter your MMSI code again to confirm. Rotate + Push 2. Push [ENT] to start entering the MMSI code. • The "MMSI" screen is displayed.  To skip the entry, push [CLR] twice. If you skip the entry, you cannot make a DSC call. To enter the code after skipping, turn OFF the power, and then turn it ON again. 3. Enter the MMSI code. Rotate + Push 7. Push Finish to set the confirmation code. • When your MMSI code is successfully entered, "MMSI Successfully Registered" is briefly displayed, and then the Main screen opens.  Your MMSI code is also displayed on the opening screen. 4. Repeat step 3 to enter all 9 digits. 5. Push the Software key Finish to set the entered code. • The "MMSI CONFIRMATION" screen is displayed. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
8
2
3
3
PREPARATION
■
Entering the MMSI code
The Maritime Mobile Service Identity (MMSI: DSC self
ID) code consists of 9 digits. You can only enter the
code when turning ON the transceiver for the first time.
This initial code can be entered only once.
After entering, it can be changed only by your dealer
or distributor.
If your MMSI code has already been entered, doing
the steps below is not necessary.
1. Hold down [
] to turn ON the transceiver.
•
Three short beeps sound, and then “Push [ENT] to
Register your MMSI” is displayed.
2.
Push [ENT] to start entering the MMSI code.
•
The “MMSI” screen is displayed.
To skip the entry, push [CLR] twice.
If you skip the entry, you cannot make a DSC call. To
enter the code after skipping, turn OFF the power, and
then turn it ON again.
3. Enter the MMSI code.
4.
Repeat step 3 to enter all 9 digits.
5. Push the Software key
Finish
to set the
entered code.
•
The “MMSI CONFIRMATION” screen is displayed.
6.
Enter your MMSI code again to confirm.
7. Push
Finish
to set the confirmation code.
•
When your MMSI code is successfully entered, “MMSI
Successfully Registered” is brie½y displayed, and then
the Main screen opens.
Your MMSI code is also displayed on the opening screen.
+
Push
Rotate
+
Push
Rotate