Lexmark W810n Setup Guide (2.8 MB) - Page 124

Aligning the finisher and the printer, Adjusting the finisher's, standing position

Get Lexmark W810n - Optra B/W Laser Printer PDF manuals and user guides
UPC - 734646367103
View all Lexmark W810n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Aligning the finisher and the printer The finisher must be parallel with the printer and the two must be at the same height, or you may have paper feeding problems. The following sections show how to check for correct alignment, and explain how to make adjustments, if necessary. Adjusting the finisher's standing position Push the finisher up against the printer, and then look at the two of them carefully from the front. If the finisher and printer resemble the figure on the left, they are properly aligned. Skip to "Adjusting the finisher's height" on page 116. 112 Set up the optional finisher

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
112
Set up the optional finisher
Aligning the finisher
and the printer
The finisher must be parallel with the
printer and the two must be at the same
height, or you may have paper feeding
problems.
The following sections show how to
check for correct alignment, and explain
how to make adjustments, if necessary.
Adjusting the finisher’s
standing position
Push the finisher up against the printer,
and then look at the two of them carefully
from the front.
If the finisher and printer resemble the
figure on the left, they are properly
aligned.
Skip to “Adjusting the finisher’s height”
on page 116.