Linksys RTP300 User Guide - Page 78

VoIP Outbound Call Routing, Parameter, Description, Values

Get Linksys RTP300 - Broadband Router With 2 Phone Ports PDF manuals and user guides
UPC - 745883565658
View all Linksys RTP300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Configuring the PSTN (FXO) Gateway How PSTN-To-VoIP Calls Work Long Silence Duration: Disconnect Tone: PSTN Line PSTN Line Detect Polarity Reversal: PSTN Line Detect Disconnect Tone: PSTN Line Silence Threshold: PSTN Line The minimum duration of continuous silence before the 10-255 Linksys ATA device disconnects the call, if the Detect (PSTN) The default is Long Silence parameter is enabled. 30(s). Tone Script of the disconnect tone to detect. The Linksys ATA device supports two frequency components. If the tone has only one frequency, use the same value for both frequencies. Each cadence segment must have the same frequency. The level value is the threshold to detect each tone. The total duration is the minimum duration of the tone to be recognized as the disconnect tone ToneScript The default is 480@30,620@30;4(.25/.25/ 1+2)" If yes, the Linksys ATA device interprets polarity reversal as a disconnect signal. On an inbound PSTN call, Linksys ATA device disconnects on the first polarity reversal. On an outbound PSTN call, Linksys ATA device disconnects on the second polarity reversal (because the first polarity reversal indicates the outbound call is connected). Yes or No The default is Yes. If yes, the Linksys ATA device interprets the disconnect tone as specified in the Disconnect Tone parameter as the disconnect signal. Yes or No The default is Yes. This is the signal energy threshold. Below this threshold is considered silence. very low, low, medium, high, very high The default is Medium. VoIP Outbound Call Routing Calls made from Line 1 are routed through the configured Line 1 service provider, by default. You can override this behavior by IP dialing, through which the calls can be routed to any IP address entered by the user. The Linksys ATA device allows flexible call routing with four sets of gateway parameters and configurable dial plans. The following table lists VoIP outbound call routing parameters. Parameter Gateway 1 GW1 Nat Mapping Enable GW1 User ID GW2 Password Web Page Line 1 Line 1 Line 1 Line 1 Description Values Fully qualified domain name (or IP address) of a Domain name or IP gateway. If the port number is not specified, 5060 is address. assumed. The default is blank. Whether to enable NAT mapping when using Gateway 1. Yes or No The default is no. The authentication user name when using Gateway 31-character string 1. The default is blank. The authentication password when using Gateway 1. 31-character string. The default is blank. Linksys ATA Administration Guide 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
Linksys ATA Administration Guide
78
How PSTN-To-VoIP Calls Work
Configuring the PSTN (FXO) Gateway
VoIP Outbound Call Routing
Calls made from Line 1 are routed through the configured Line 1 service provider, by default.
You can override this behavior by IP dialing, through which the calls can be routed to any IP
address entered by the user. The Linksys ATA device allows flexible call routing with four sets of
gateway parameters and configurable dial plans. The following table lists VoIP outbound call
routing parameters.
Long Silence Duration:
PSTN
Line
The minimum duration of continuous silence before the
Linksys ATA device disconnects the call, if the
Detect (PSTN)
Long Silence
parameter is enabled.
10-255
The default is
30(s)
.
Disconnect Tone:
PSTN
Line
Tone Script of the disconnect tone to detect. The Linksys
ATA device supports two frequency components. If the
tone has only one frequency, use the same value for both
frequencies.
Each cadence segment must have the same frequency.
The level value is the threshold to detect each tone.
The total duration is the minimum duration of the tone to
be recognized as the disconnect tone
ToneScript
The default is
480@-
30,620@-
30;4(.25/.25/
1+2)”
Detect Polarity Reversal:
PSTN
Line
If yes, the Linksys ATA device interprets polarity reversal as
a disconnect signal.
On an inbound PSTN call, Linksys ATA device disconnects
on the first polarity reversal. On an outbound PSTN call,
Linksys ATA device disconnects on the second polarity
reversal (because the first polarity reversal indicates the
outbound call is connected).
Yes or No
The default is
Yes
.
Detect Disconnect Tone:
PSTN
Line
If yes, the Linksys ATA device interprets the disconnect
tone as specified in the
Disconnect Tone
parameter as the
disconnect signal.
Yes or No
The default is
Yes
.
Silence Threshold:
PSTN
Line
This is the signal energy threshold. Below this threshold is
considered silence.
very low, low,
medium,
high, very
high
The default is
Medium
.
Parameter
Web
Page
Description
Values
Gateway 1
Line 1
Fully qualified domain name (or IP address) of a
gateway. If the port number is not specified, 5060 is
assumed.
Domain name or IP
address.
The default is blank.
GW1 Nat
Mapping Enable
Line 1
Whether to enable NAT mapping when using
Gateway 1.
Yes or No
The default is
no
.
GW1 User ID
Line 1
The authentication user name when using Gateway
1.
31-character string
The default is blank.
GW2 Password
Line 1
The authentication password when using Gateway 1.
31-character string.
The default is blank.