Linksys SPA922 Cisco SPA9000 Voice System Web-UI Based Product Installation an - Page 50

Upgrading the Firmware for the SPA9000, To factory reset the SPA9000 if needed

Get Linksys SPA922 - IP Phone With Switch PDF manuals and user guides
UPC - 745883570836
View all Linksys SPA922 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Connecting the Equipment Installing the SPA9000 4 To factory reset the SPA9000 (if needed) NOTE If your SPA9000 has been used before, we recommend performing a factory reset. Otherwise, proceed with enabling WAN Access. a. Lift the receiver on the analog phone that is connected to the Phone 1 port. NOTE There is no dial tone from the IVR. b. Press the star key (*) four times: **** c. When the IVR responds, press the code for factory reset: 73738# d. When prompted, press the code to confirm: 1# e. Wait about 30 seconds while the system reboots. Upgrading the Firmware for the SPA9000 In this procedure, you install any firmware updates that you downloaded in the Preparation phase. STEP 1 Use the IVR to check the IP address of the SPA9000: a. Pick up the receiver of the analog phone that you connected to the SPA9000. b. Press **** and then press 110#. c. Make a note of the IP address that is announced. STEP 2 Use the administration computer to install the latest firmware: a. Extract the Zip file, and then run the executable file to upgrade the firmware. b. When the Firmware Upgrade Warning window appears, click Continue. SPA9000 Voice System Installation and Configuration Guide for Web UI 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
Connecting the Equipment
Installing the SPA9000
SPA9000 Voice System Installation and Configuration Guide for Web UI
48
4
To factory reset the SPA9000 (if needed)
NOTE
If your SPA9000 has been used before, we recommend performing a factory reset.
Otherwise, proceed with enabling WAN Access.
a.
Lift the receiver on the analog phone that is connected to the Phone 1 port.
NOTE
There is no dial tone from the IVR.
b.
Press the star key (*) four times: ****
c.
When the IVR responds, press the code for factory reset: 73738#
d.
When prompted, press the code to confirm: 1#
e.
Wait about 30 seconds while the system reboots.
Upgrading the Firmware for the SPA9000
In this procedure, you install any firmware updates that you downloaded in the
Preparation phase.
STEP 1
Use the IVR to check the IP address of the SPA9000:
a.
Pick up the receiver of the analog phone that you connected to the SPA9000.
b.
Press
****
and then press
110#
.
c.
Make a note of the IP address that is announced.
STEP 2
Use the administration computer to install the latest firmware:
a.
Extract the Zip file, and then run the executable file to upgrade the firmware.
b.
When the
Firmware Upgrade
Warning
window appears, click
Continue
.