Linksys SPA922 Cisco SPA9000 Voice System Web-UI Based Product Installation an - Page 63

Configuring the SPA400 Network Connection, SPA9000 Voice System, Administration Guide - reset admin password

Get Linksys SPA922 - IP Phone With Switch PDF manuals and user guides
UPC - 745883570836
View all Linksys SPA922 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Connecting the Equipment Installing the SPA400 4 Configuring the SPA400 Network Connection You need to configure a fixed IP address for your SPA400. STEP 1 Start Internet Explorer, and enter the IP address of the SPA400. • By default, the SPA400 is configured to obtain an IP Address via DHCP. You can check the obtained IP address on the router DHCP server's client list. • If your SPA400 has been used before or it is not reachable, factory reset the unit by pressing the Reset button for 10 seconds. STEP 2 When the password prompt appears, enter the default user name, Admin, with no password. Then click OK. NOTE The user name must be entered exactly as shown: Admin. For information about managing system access, refer to the Cisco SPA9000 Voice System Administration Guide. STEP 3 Click Setup tab > Basic Setup. SPA9000 Voice System Installation and Configuration Guide for Web UI 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
Connecting the Equipment
Installing the SPA400
SPA9000 Voice System Installation and Configuration Guide for Web UI
61
4
Configuring the SPA400 Network Connection
You need to configure a fixed IP address for your SPA400.
STEP 1
Start Internet Explorer, and enter the IP address of the SPA400.
•
By default, the SPA400 is configured to obtain an IP Address via DHCP. You can
check the obtained IP address on the router DHCP server’s client list.
•
If your SPA400 has been used before or it is not reachable, factory reset the
unit by pressing the Reset button for 10 seconds.
STEP 2
When the password prompt appears, enter the default user name,
Admin
, with no
password. Then click
OK
.
NOTE
The user name must be entered exactly as shown:
Admin
. For information
about managing system access, refer to the
Cisco
SPA9000 Voice System
Administration Guide
.
STEP 3
Click
Setup tab > Basic Setup
.