Linksys SPA922 Cisco SPA9000 Voice System Web-UI Based Product Installation an - Page 81

Signalling Port, RTP Port, Session Timer, Voice, Packetization, Setup tab > SPA9000 Interface

Get Linksys SPA922 - IP Phone With Switch PDF manuals and user guides
UPC - 745883570836
View all Linksys SPA922 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Configuring Phone Service and Voice Mail Configuring the SPA400 STEP 1 Click Setup tab > SPA9000 Interface. 5 STEP 2 Enter the following settings: • User ID: 9000 This is the user ID that the SPA9000 will use to register with the SPA400. Any ID can be used, but must match exactly the User ID that you entered on the corresponding SPA9000 Voice > Line page. • SPA9000 Address: Select the Discover Automatically radio button (required for SPA9000 operation). This setting enables the SPA400 to learn the IP address and the UDP port of the SPA9000 the from the SIP Registration packets sent by SPA9000. • Call Signalling Packets: 68 • RTP Packets: b8 • Leave the Signalling Port at the default value of 5060. This port is the source port that is used to originate signaling between the SPA400 and the SPA9000. • Leave the RTP Port at the default value of 10000. This port is the base UDP port for the block of UDP ports that the SPA400 uses to send and receive RTP and RTCP packets. • Leave the Session Timer fields at the default values: Enabled with 0 seconds in both Refresh Time fields. STEP 3 Click Save Settings at the bottom of the page. STEP 4 Click Setup tab > Voice. STEP 5 Enter the following settings on the Voice page: • Preferred Codec: Select G.711u. • Packetization: Choose 30ms from the Packetization drop-down list for G.711U. • VAD: Choose OFF from the VAD drop-down list for G.711U. SPA9000 Voice System Installation and Configuration Guide for Web UI 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
Configuring Phone Service and Voice Mail
Configuring the SPA400
SPA9000 Voice System Installation and Configuration Guide for Web UI
79
5
STEP 1
Click
Setup tab > SPA9000 Interface
.
STEP 2
Enter the following settings:
•
User ID:
9000
This is the user ID that the SPA9000 will use to register with the SPA400. Any ID
can be used, but must match exactly the User ID that you entered on the
corresponding SPA9000 Voice > Line page.
•
SPA9000 Address: Select the
Discover Automatically
radio button (required for
SPA9000 operation). This setting enables the SPA400 to learn the IP address
and the UDP port of the SPA9000 the from the SIP Registration packets sent by
SPA9000.
•
Call Signalling Packets:
68
•
RTP Packets:
b8
•
Leave the
Signalling Port
at the default value of 5060. This port is the source
port that is used to originate signaling between the SPA400 and the SPA9000.
•
Leave the
RTP Port
at the default value of 10000. This port is the base UDP
port for the block of UDP ports that the SPA400 uses to send and receive RTP
and RTCP packets.
•
Leave the
Session Timer
fields at the default values: Enabled with 0 seconds in
both
Refresh Time
fields.
STEP 3
Click
Save Settings
at the bottom of the page.
STEP 4
Click
Setup tab > Voice
.
STEP 5
Enter the following settings on the
Voice
page:
•
Preferred Codec: Select
G.711u
.
•
Packetization: Choose
30ms
from the
Packetization
drop-down list for G.711U.
•
VAD: Choose
OFF
from the
VAD
drop-down list for G.711U.