Maytag MGDZ400TQ Use and Care Guide - Page 19

To use a Sensor Dry Cycle • Select a Sensor [Dry Cycle. Sensor Dry Cycles are preset to Normal Cycle. • Select DRYNESS I.EVEI. to adjust how dry you want the load. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected dryness level. To make changes to the Dryness Level and/or Options during a Sensor Dry Cycle: • Press PAUSE/CANCEl once. • Adjust Dryness I.evel and/or Options. NOTE: Dryness I.evel selections can be made only while using Sensor Dry Cycles. Selecting More, Normal or I.ess automatically adjusts the sensed time needed. M 0 RE I NORMAL LESS © DRYNESS LEVEL SENSOR DRY ONLY Sensor Dry cycles take the guesswork out of drying time and enhances fabric care. The amount of time that is displayed is the estimated time remaining in the cycle. To use a Timed Dry Cycle • Select a Nmed [Dry Cycle. • Press the Timed Dry Cycle Adjust Up or [Down arrow buttons until the desired drying time is displayed, lap the limed L)ry Cycle Adjust Up or L)own arrow buttons and the time will change by 1-minute intervals. Press and hold the Timed Dry Cycle Adjust Up or [])own arrow buttons, and the time will change by S-minute intervals. NOTE: The Timed Dry Cycle Adjust feature can be used only with Timed [Dry Cycles. ADJUST _ TIMED DRYCYCLE • Press TEMPERATURE until the desired temperature illuminates. To make changes to Time and/or options during a Timed Dry Cycle: • Press PAUSE/CANCEl once. • Adjust the Time and/or Options. 5. iOPT[ONAL STEP) [f desired, select WRINKLE PREVENT. For more details, see "WR[NK[E PREVENT" in the "Additional Features" section. 6. iOPT[ONAL STEP) The Cycle Signal is preset to on. [f desired, you may turn the Cycle Signal off by pressing the Cycle Signal button. 7. Press and hold START for approximately closed. 1 second until dryer starts. Be sure the door is • [f you do not press Start within 5 minutes of selecting a cycle, the dryer automatically shuts off. To pause/stop the dryer at any time Open the door or press PAUSE/CANCEl once. To restart the dryer Close the door. Press and hold START until dryer starts. To end/cancel your dryer at any time Press PAUSE/CANCEl. twice or open the door. NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer. / < "L', ......... This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the control lock feature to avoid unintended cycle or option changes during dryer operation. ...... To enable the control lock feature: (,i: Press and hold CYCI.E SIGNAl. button for 3 seconds. The CONTROI.S lOCKED icon lights up, and a single beep tone is heard. To unlock, press and hold CYCLE SIGNAl button for 3 seconds. The indicator light turns off. Select the correct cycle and dryness level or temperature for your load. If a Sensor [Dry Cycle is running, @e display shows @e esfim_ted cycle time, which is determined by your dryer automatically sensing the dryness level of your load. If a Timed Dry Cycle is running, the display shows the exact number of minutes remaining in the cycle. Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level. Drying tips • Follow care label directions when they are available. • If desired, add a fabric softener sheet. Follow package instructions. • [b reduce wrinkling, remove the load from the dryer as soon as tumbling stops. ]his is especially important for permanent press, knits, and synthetic fabrics. • Avoid drying heavy work clothes together with lighter fabrics. This could cause overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.