Netgear WGX102 WGX102v2 Reference Manual - Page 117

Restoring the Default WGX102 Configuration and Password, Problems with Router Mode Only Date and Time

Get Netgear WGX102 - 54 Mbps Wall-Plugged Wireless Range Extender PDF manuals and user guides View all Netgear WGX102 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102 Restoring the Default WGX102 Configuration and Password This section explains how to restore the factory default configuration settings, changing the wireless range extender's administration password to password and the IP address to 192.168.0.101. You can erase the current configuration and restore factory defaults in two ways: • Use the Erase function of the wireless range extender (see "Erasing the Configuration" on page 6-10). • Use the default reset button on the bottom of the WGX102. Use this method for cases when the administration password or IP address is not known. To restore the factory default configuration settings without knowing the administration password or IP address, you must use the default reset button on the bottom panel of the WGX102. 1. Plug in the WGX102 upside down, so the bottom is facing up. 2. A small hole (reset) is visible on the bottom of the device. 3. Use a paper clip to press and hold the reset for at least 15 seconds. 4. Release the reset button. If the wireless range extender fails to restart or the power light continues to blink, the unit may be defective. If the error persists, you might have a hardware problem and should contact technical support. Problems with Router Mode Only Date and Time The E-Mail menu in the Content Filtering section displays the current date and time of day. The Wireless Range Extender uses the Network Time Protocol (NTP) to obtain the current time from one of several Network Time Servers on the Internet. Each entry in the log is stamped with the date and time of day. Problems with the date and time function can include: • Date shown is January 1, 2000. Cause: The wireless range extender has not yet successfully reached a Network Time Server. Check that your Internet access settings are configured correctly. If you have just completed configuring the WGX102, wait at least five minutes and check the date and time again. • Time is off by one hour. Cause: The WGX102 does not automatically sense Daylight Savings Time. In the E-mail menu, select or clear the Adjust for Daylight Savings Time check box. Troubleshooting 8-7 202-10042-02 v1.1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
Reference Manual for the 54 Mbps Wall-Plugged Wireless Range Extender WGX102
Troubleshooting
8-7
202-10042-02 v1.1
Restoring the Default WGX102 Configuration and Password
This section explains how to restore the factory default configuration settings, changing the
wireless range extender’s administration password to
password
and the IP address to
192.168.0.101
. You can erase the current configuration and restore factory defaults in two ways:
•
Use the Erase function of the wireless range extender (see
“Erasing the Configuration” on
page 6-10
).
•
Use the default reset button on the bottom of the WGX102. Use this method for cases when
the administration password or IP address is not known.
To restore the factory default configuration settings without knowing the administration password
or IP address, you must use the default reset button on the bottom panel of the WGX102.
1.
Plug in the WGX102 upside down, so the bottom is facing up.
2.
A small hole (reset) is visible on the bottom of the device.
3.
Use a paper clip to press and hold the reset for at least 15 seconds.
4.
Release the reset button.
If the wireless range extender fails to restart or the power light continues to blink, the unit may
be defective. If the error persists, you might have a hardware problem and should contact
technical support.
Problems with Router Mode Only Date and Time
The E-Mail menu in the Content Filtering section displays the current date and time of day. The
Wireless Range Extender uses the Network Time Protocol (NTP) to obtain the current time from
one of several Network Time Servers on the Internet. Each entry in the log is stamped with the date
and time of day. Problems with the date and time function can include:
•
Date shown is January 1, 2000. Cause: The wireless range extender has not yet successfully
reached a Network Time Server. Check that your Internet access settings are configured
correctly. If you have just completed configuring the WGX102, wait at least five minutes and
check the date and time again.
•
Time is off by one hour. Cause: The WGX102 does not automatically sense Daylight Savings
Time. In the E-mail menu, select or clear the Adjust for Daylight Savings Time check box.