Sony HDWD1800 Operation Manual - Page 56

Shot Mark Operations

Get Sony HDWD1800 PDF manuals and user guides View all Sony HDWD1800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

6-2 Shot Mark Operations This section describes the operations concerning reading and writing shot marks. Note that the following operations cannot be carried out by remote control. Shot mark operations are carried out from function menu page P104: SHOT MRK. Select F3 (SHOT MRK) in function menu page P05: MISC-2 to open function menu page P104: SHOT MRK. SHOT MRK REC/ERS REC REC SHOT MRK MARK LIST 190 shot marks have already been read in, only 10 shot marks will be read from the new tape. In the shot mark list (see page 57) the data from different cassettes is separated by a separator. 6-2-2 Writing Shot Marks To write recording start marks during recording In setup menu item 631 "REC START MARK MODE", select whether or not to write a recording start mark for each of the three recording modes (CRASH REC, ASSEMBLE, INSERT). When you set a particular mode to "ON", a recording start mark is written on the tape each time you start recording in that mode. Note EXIT When using the insert edit mode, select F2 (INS TC) in function menu page P07: E.PRESET, turning it on. 6-2-1 Reading Shot Marks To read in shot marks With a cassette tape loaded and F7 (LIST) selected, press the F FWD or REW button. While the shot marks are being read in, the F FWD or REW button flashes. The unit searches to the end of the tape, then rewinds automatically. For the procedure for listing the read shot marks, see page 57. Note It is possible to read in a maximum of 200 shot marks. When 200 shot marks have been read in, the ancillary message display on the control panel shows "SHOT LIST FULL", and the reading stops. To cancel the message, press one of the tape transport buttons. To stop reading Press the STOP button. To read shot marks from more than one cassette After changing the cassettes, carry out the reading operation again. Data written in the new cassette will be added as long as the total does not exceed 200 shot marks. For example, if To write shot mark 1, shot mark 2 or post marks To select the type of shot mark to be written In setup menu item 636 "MARK SELECT IN REC/ ASSEMBLE", select SHOT1, SHOT2 or POST mark. Note If any of the mode settings in setup menu item 631 "REC START MARK MODE" is set to "ON" (to write a recording start mark), then the user bits are overwritten with the shot mark data for 20 frames from the start of recording in crash recording mode, assemble edit mode or insert edit mode. To write in crash recording or assemble editing 1 Holding down the SHIFT/ENTRY button, select F2 (REC/ERS) in function menu page P104: SHOT MRK to set "REC". Note A mark can be written only when F2 is set to "REC". 2 At the position you want to write the mark, hold down the SHIFT/ENTRY button and select F3 (REC). A mark of the type selected in the setup menu item 636 is written. Chapter 6 Shot Mark Function 56 6-2 Shot Mark Operations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
56
6-2
Shot Mark Operations
Chapter 6
Shot Mark Function
6-2
Shot Mark Operations
This section describes the operations concerning reading
and writing shot marks. Note that the following operations
cannot be carried out by remote control.
Shot mark operations are carried out from function menu
page P104: SHOT MRK. Select F3 (SHOT MRK) in
function menu page P05: MISC-2 to open function menu
page P104: SHOT MRK.
6-2-1
Reading Shot Marks
To read in shot marks
With a cassette tape loaded and F7 (LIST) selected, press
the F FWD or REW button.
While the shot marks are being read in, the F FWD or
REW button flashes.
The unit searches to the end of the tape, then rewinds
automatically.
For the procedure for listing the read shot marks, see
page 57.
It is possible to read in a maximum of 200 shot marks.
When 200 shot marks have been read in, the ancillary
message display on the control panel shows “SHOT LIST
FULL”, and the reading stops.
To cancel the message, press one of the tape transport
buttons.
To stop reading
Press the STOP button.
To read shot marks from more than one
cassette
After changing the cassettes, carry out the reading
operation again.
Data written in the new cassette will be added as long as
the total does not exceed 200 shot marks. For example, if
190 shot marks have already been read in, only 10 shot
marks will be read from the new tape.
In the shot mark list
(see page 57)
the data from different
cassettes is separated by a separator.
6-2-2
Writing Shot Marks
To write recording start marks during
recording
In setup menu item 631 “REC START MARK MODE”,
select whether or not to write a recording start mark for
each of the three recording modes (CRASH REC,
ASSEMBLE, INSERT).
When you set a particular mode to “ON”, a recording start
mark is written on the tape each time you start recording in
that mode.
When using the insert edit mode, select F2 (INS TC) in
function menu page P07: E.PRESET, turning it on.
To write shot mark 1, shot mark 2 or post
marks
To select the type of shot mark to be written
In setup menu item 636 “MARK SELECT IN REC/
ASSEMBLE”, select SHOT1, SHOT2 or POST mark.
If any of the mode settings in setup menu item 631 “REC
START MARK MODE” is set to “ON” (to write a
recording start mark), then the user bits are overwritten
with the shot mark data for 20 frames from the start of
recording in crash recording mode, assemble edit mode or
insert edit mode.
To write in crash recording or assemble editing
1
Holding down the SHIFT/ENTRY button, select F2
(REC/ERS) in function menu page P104: SHOT MRK
to set “REC”.
A mark can be written only when F2 is set to “REC”.
2
At the position you want to write the mark, hold down
the SHIFT/ENTRY button and select F3 (REC).
A mark of the type selected in the setup menu item 636
is written.
Note
SHOT MRK
REC/ERS
REC
REC
SHOT MRK
MARK
LIST
EXIT
Note
Note
Note