Sony HDWD1800 Operation Manual - Page 66
P02: TC
View all Sony HDWD1800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 66 highlights
Item F8 (COUNTER) F9 (MENU) F10 (TCG SET) Setting Select the time data to display in time data display (see page 17). TC: Playback timecode read by the internal timecode reader, or recording timecode. The LTC or VITC time data type indicator (see page 18) lights.b) UB: User bits data of playback timecode or recording timecode. The LUB or VIUB time data type indicator lights, depending on whether the timecode is LTC or VITC.b) CTL: The running time of the tape being played back or recorded, as calculated from a count of CTL signals recorded on the tape. The time is displayed in Hours:Minutes:Seconds:Frames format. Puts the system into setup menu mode (see Chapter 9). (Jump to P108: SETUP (TOP)) When the current setup menu settings are the same as the contents of any of menu banks 1 to 4, or the factory defaults,the corresponding indication (BANK1), (BANK2), (BANK3), (BANK4) or (DEFLT) appears below the time data display on the LCD. • When F8 (COUNTER) is set to "TC", a screen appears that allows you to set the initial value of the timecode generated by the internal timecode generator (see page 17).c) • When F8 (COUNTER) is set to "UB", a screen appears that allows you to set the timecode user bits (see page 17).c) a) CONFI playback is disabled during editing. b) The selection of LTC or VITC depends on the setting of F10 (TCR) in function menu page P02: TC. c) Setting screen is not displayed when F1 (TCG SRC) is set to "INTERNAL" and F2 (TCG MODE) is set to "PRESET" in function menu page P02: TC. P02: TC This is a function menu page for setting items relating to timecode. Item Setting F1 (TCG SRC) Select the signal source of the timecode with which the internal timecode generator synchronizes. INTERNAL: Synchronizes according to the initial preset value set by control panel operation or by control from the device connected to the REMOTE1-IN (9P) connector, or synchronize with the timecode of the playback tape. EXT LTC: Synchronizes with the external timecode signal input to the TIME CODE IN connector. VID IN: Synchronizes with the timecode data superimposed on the HDSDI signal input to the HDSDI INPUT connector or on the MPEG TS signal input to the HDV IN connector (when an optional HKDW-105 i.LINK (HDV) Input Board is installed). F2 (TCG MODE) Select one of the following for timecode regenerated by the internal timecode generator. PRESET: Presets the initial value of timecode generated by the internal timecode generator, as specified by control panel operation or by control from the device connected to the REMOTE1-IN (9P) connector. This operation is enabled when F1 (TCG SRC) is set to "INTERNAL". RGN: LTC: Regenerates by synchronizing with the LTC timecode value read by the internal timecode reader. RGN: VITC: Regenerates by synchronizing with the VITC timecode value read by the internal timecode reader. F3 (TCG RUN) Select one of the following running modes for the internal timecode generator. FREE: Timecode continues to increase as long as the unit is powered on, regardless of the unit's operating mode. REC: Timecode increases during recording only. If you select this mode, you should also set F1 (TCG SRC) to "INTERNAL", and set F2 (TCG MODE) to "PRESET" in this menu page. F4 (DROP FRM) In 59.94i, 29.97PsF mode, select dropframe or non-drop-frame mode for the timecode generator and the CTL counter. DF: Drop-frame mode NDF: Non-drop-frame mode F5 (No function assigned) F6 (No function assigned) F7 (No function assigned) F8 (No function assigned) F9 (No function assigned) Chapter 8 Function Menu 66 8-2 Function Menu Item List