Sony HDWD1800 Operation Manual - Page 78

Chapter 9 Setup Menus 9-3 Items in the Basic Setup Menu The basic setup menu contains the following items. In the "Settings" column of the table, the factory default settings are underlined. Item number Item name 001 PREROLL TIME 002 a) CHARACTER H-POSITION 003 a), b) CHARACTER V-POSITION 004 SYNCHRONIZE 005 DISPLAY INFORMATION SELECT 006 LOCAL FUNCTION ENABLE Settings 0S to 5S to 30S: Set the preroll time in the range from 0 to 30 seconds. A preroll time of at least 5 seconds is recommended when using this unit for editing. Adjust the horizontal position of the character information output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector, SDI OUTPUT 3 (SUPER) connector, or HDSDI OUTPUT 3 (SUPER) connector for superimposed display on the monitor. 0 to 1E to 3C (59.94i, 29.97PsF, 23.98PsF mode)/0 to 1B to 36 (50i, 25PsF, 24PsF mode): The hexadecimal value 00 is for the far left of the screen and increasing the value moves the position of the characters to the right. Adjust the vertical position of the first line of the character information output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector, HDSDI OUTPUT 3 (SUPER) connector, and SDI OUTPUT 3 (SUPER) connector for superimposed display on the monitor. 0 to 57 to 6C (59.94i, 29.97PsF, 23.98PsF mode)/0 to 70 to 88 (50i, 25PsF, 24PsF mode): The hexadecimal value 00 is for the top of the screen and increasing the value lowers the position of the characters. When editing using this unit as a controller and an external VTR connected to this unit via a 9-pin remote control cable, this item determines whether or not to operate the two units in phase synchronization. OFF: Do not operate in phase synchronization. ON: Operate in phase synchronization. Determine the type of text information to be output from the COMPOSITE VIDEO OUTPUT 3 (SUPER), SDI OUTPUT 3 (SUPER) and HDSDI OUTPUT 3 (SUPER) connectors when F5 (CHARA) is set to "ON" in function menu page P04: MISC-1. T&STA: Time data display information and the unit's status T&UB: Time data display information and the user bits T&CTL: Time data display information and CTL T&T: Time data display information and timecode (LTC or VITC) TIME: Timecode (LTC or VITC) only If there is an overlap between the setting of this item and the setting of the control panel, it is automatically avoided. For example, if CTL is selected on the control panel and this menu item setting is "T&CTL", then CTL and LTC are output. Determine which buttons on the control panel are enabled when this unit is controlled from external equipment. DIS: All buttons and switches are disabled. S&E&P: Only the STOP button, EJECT button, P1 to P5 and DISPLAY buttons are enabled. ENA: All buttons and switches are enabled. MAP: Follow the LOCAL KEY MAP setting. For information about setting the LOCAL KEY MAP, see menu item 023 "LOCAL KEY MAP" (page 79). 007 TAPE TIMER DISPLAY Determine whether to display the CTL count in 12-hour mode or 24-hour mode. + -12H: 12-hour mode 24H: 24-hour mode 008 MONITORING For two-VTR editing with the monitor connected only to the recorder, determines SELECTION FOR VTR- whether the recorder is forced into E-E mode when the recorder's PLAYER button TO-VTR EDIT is pressed to view the player's playback signals on the monitor. MANU: Do not force the recorder into E-E mode. AUTO: Set the recorder to E-E mode, so that the playback signals of the player are output to the video monitor. 78 9-3 Items in the Basic Setup Menu