Toshiba 40L2200U User Guide - Page 54

Setup, Installation, ENTER, Sample Illustration Setup menu - Installation selection

Get Toshiba 40L2200U PDF manuals and user guides View all Toshiba 40L2200U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

54 Setting up your TV Storing channels in memory (optional) NOTE ❖ You must set up the ANT/CABLE input source before programming channels. See "ANT/CABLE IN" on page 52. ❖ The automatic channel programming process will erase channels that were previously programmed into the TV's memory. ❖ To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. ❖ Programming channels when the ANT/CABLE input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. To program channels automatically: 1 Configure the antenna input source. If you have not already done so, see "ANT/CABLE IN" on page 52. 2 Press the MENU button and open the Setup menu. 3 Highlight Installation, and then press the ENTER button. (Sample Illustration) Setup menu - Installation selection

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
54
Setting up your TV
Storing channels in memory (optional)
❖
You must set up the ANT/CABLE input source before
programming channels. See
“ANT/CABLE IN” on page 52
.
❖
The automatic channel programming process will erase
channels that were previously programmed into the TV’s
memory.
❖
To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
❖
Programming channels when the ANT/CABLE input is
configured for Cable will take substantially longer than when the
antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should not
have to repeat the programming process again unless your
Cable TV service lineup changes significantly.
To program channels automatically:
1
Configure the antenna input source. If you have not already
done so, see
“ANT/CABLE IN” on page 52
.
2
Press the
MENU
button and open the
Setup
menu.
3
Highlight
Installation
, and then press the
ENTER
button.
(Sample Illustration) Setup menu - Installation selection
NOTE