Yamaha DTX-MULTI Owner's Manual - Page 103

Reference KIT VOICE TRIGGER Setting Area (TRG) TRG2-2-2 Individual Crosstalk Level page 1 TRG2-2-2 Level=≥25%(¡£) 32 1 Pad Use this parameter to select the pad(s) for which a crosstalk level is to be set. You can also strike a pad to select it. Settings UP, MID, LOW, or 01 to 17 NOTE • Selection by striking is limited to pad groups (i.e., UP, MID, or LOW) and the external pads (i.e., 13 to 17). B Crosstalk source Use this parameter to specify a pad or group of pads causing crosstalk in the pad(s) indicated by 1. You can also strike a pad to select it. Settings UP, MID, LOW, or 01 to 17 C Crosstalk level Use this parameter to specify a level for preventing crosstalk from the pad(s) indicated by 2. If the input level produced at the pad indicated by 1 is lower than this level whenever the pad indicated by 2 is struck, it will be treated as crosstalk and no trigger signal will be generated. Although higher setting values are more effective in preventing crosstalk, they can also make it difficult to play multiple pads at the same time. Settings 0% to 99% Typical Examples of CrosstalkPrevention Setup - No. 1 ● Use this approach when pad sensitivity is set to allow playing by hand and striking of one of the pads from the MID group (i.e., 4 to 9) causes another pad from that group to produce a sound. 1 Navigate to the Individual Crosstalk Level page (TRG2-2-2) and set its parameters as follows. 1: MID (i.e., pads 4 to 9), 2: MID (i.e., pads 4 to 9) 2 Hold down the [SHIFT] button and press the [UP/ DOWN] button to activate the input lock. (-MIDwill change to [MID].) NOTE • The input lock must be activated here to prevent the selection from changing when one of the other pads from the MID group (i.e., 4 to 9) is struck in the next step. 3 While striking one of the pads from the MID group (i.e., 4 to 9), raise the level indicated by 3 until other pads from that group no longer produce any sound. 1 TRG2-2-2≥[MID]˛¸ Level=≥28%(MID) 2 3 4 Press the [STORE] button to open the Trigger Store page, and then store your trigger setup as described on page 45. Typical Examples of CrosstalkPrevention Setup - No. 2 ● Use this approach when pad sensitivity is set to allow playing by hand and, for example, striking of Pad 4 also results in Pad 5 producing a sound 1 Navigate to the Individual Crosstalk Level page (TRG2-2-2) and set its parameters as follows. 1: 05 (i.e., Pad 5), 2: 04 (i.e., Pad 4) 2 Hold down the [SHIFT] button and press the [UP/ DOWN] button to activate the input lock. (-º∞will change to [º∞] .) NOTE • The input lock must be activated here to prevent the selection changing from Pad 5 to Pad 4 when Pad 4 is struck in the next step. 3 While striking Pad 4, raise the level indicated by 3 until Pad 5 no longer causes a voice to play (i.e., no longer produces a trigger signal). NOTE • If this level is set too high, Pad 5 may not produce any sound when struck relatively softly together with Pad 4. 1 TRG2-2-2 Level=≥28%(04) 32 4 Press the [STORE] button to open the Trigger Store page, and then store your trigger setup as described on page 45. MIDI WAVE PATTERN UTILITY TRIGGER Owner's Manual 103