Yamaha DTX-MULTI Owner's Manual - Page 48
Effect Send Levels, Variation Effect Setup, Chorus Send Reverb Send Variation Type
View all Yamaha DTX-MULTI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 48 highlights
KIT Setting Area (KIT) KIT3 EFFECT SEND Effect Send Levels KIT4 VARIATION Variation Effect Setup KIT3 ≥≥EFFECT≥SEND In the EFFECT SEND section, you can adjust the degree to which chorus and reverb effects are applied to the entire drum kit. With the EFFECT SEND page (KIT3) displayed, press the [ENTER] button to access its two parameter-setting pages (KIT3-1 and KIT3-2). You can use the [B]/[C] buttons to switch between these pages. KIT3-1 Chorus Send page Using the Chorus Send page, you can adjust the degree to which the chorus effect is applied to all drum voices in the currently selected kit. If any of the kit's individual voices also have a chorus-send level set on the VOICE area's Chorus Send page (VCE42), chorus will be assigned to them in line with the sum of both send levels. KIT3-1≥≥ ≥ChorusSend=≥≥0 1 1 Chorus send level (ChorusSend) Use this parameter to set the chorus-send level for the currently selected drum kit. Settings 0 to 127 NOTE • If you change the chorus-send level for MIDI channel 10 on the MIDI area's Chorus Send page (MIDI3-6), the ChorusSend parameter on this page (KIT3-1) will be automatically set to the same value. The reverse does not apply, however - in other words, the chorus send setting on the MIDI area's Chorus Send page (MIDI3-6) is not affected by changes made on this page (KIT3-1). KIT3-2 Reverb Send page Using the Reverb Send page, you can adjust the degree to which the reverb effect is applied to all drum voices in the currently selected kit. If any of the kit's individual voices also have a reverb-send level set on the VOICE area's Reverb Send page (VCE4-3), reverb will be assigned to them in line with the sum of both send levels. KIT3-2≥≥ ≥ReverbSend=≥35 1 1 Reverb send level (ReverbSend) Use this parameter to set the reverb-send level for the currently selected drum kit. Settings 0 to 127 NOTE • If you change the reverb-send level for MIDI channel 10 on the MIDI area's Reverb Send page (MIDI3-7), the ReverbSend parameter on this page (KIT3-1) will be automatically set to the same value. The reverse does not apply, however - in other words, the reverb send setting on the MIDI area's Reverb Send page (MIDI3-7) is not affected by changes made on this page (KIT3-2). KIT4 ≥≥≥VARIATION In the VARIATION section, you can select a variation effect, adjust the degree to which it is applied, and configure it in a number of other ways. Variation effects are applied to all voices (on all MIDI channels). With the VARIATION page (KIT4) displayed, press the [ENTER] button to access its five parameter-setting pages (KIT4-1 to KIT4-5). You can use the [B]/[C] buttons to navigate between these pages. KIT4-1 Variation Type page KIT4-1≥≥VarType= C&E/Compressor 1 2 1 Variation category Use this parameter to select a variation-effect category. Settings Refer to the separate Data List booklet. B Variation type Use this parameter to select a variation-effect type. Settings Refer to the separate Data List booklet. With an effect category and type selected, you can press the [ENTER] button on the Variation Type page (KIT4-1) to access a range of setting pages allowing each of the selected effect's parameters to be set. (The number of parameter-setting pages depends on the effect selected.) Use the [B]/[C] buttons to navigate between these pages. KIT4-1-1 Parameter setting page (example) KIT4-1-1≥≥≥ LFOSpeed=0.000Hz 1 1 Effect parameter Each parameter setting page contains a different parameter for the selected variation effect. Settings Refer to the separate Data List booklet. 48 Owner's Manual