Yamaha DTX-MULTI Owner's Manual - Page 65

Reference KIT VOICE MIDI Setting Area (MIDI) MIDI1-8 Trigger Polyphony page MIDI1-8≥-º¡- 1 TrgMonoPoly=poly 2 1 Pad number Settings 01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW, HHCL, or HHSP B Trigger mono/poly (TrgMonoPoly) Use this parameter to control what happens when the pad indicated by 1 is struck repeatedly. • mono ........ The previous sound will be stopped before a new sound starts. • poly .......... Previous sounds will continue to play when a new sound starts. Settings mono or poly NOTE • If no note numbers have been assigned to any of the pad's layers (A to D) on the MIDI Note page (MIDI1-2), this setting will be displayed as "--" and modification will not be possible. • MIDI Note Off messages are not sent when "off" has been selected on the Receive Key-Off page (MIDI1-5). If you want to set trigger monophony, therefore, be sure to set this parameter to "on". This will ensure that Note Off messages are sent to prevent overlapping voices. MIDI1-9 Trigger Alternate Group page MIDI1-9 1 TrgAltGrp=off 2 1 Pad number Settings 01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW, HHCL, or HHSP B Trigger alternate group (TrgAltGrp) Use this parameter to assign the pad indicated by 1 to an alternate group if so required. Alternate groups are monophonic sets of pads, and therefore, only one pad from an alternate group can be producing a sound at any time. If a pad is struck while another pad from the same alternate group is already producing a sound, a MIDI Note Off message will be sent for the first pad together with the MIDI Note On message for the second. In order to use trigger alternate groups with voices played on MIDI channel 10, the sending of MIDI Note Off messages must be enabled by selecting "on" for RcvKeyOff on the Receive Key-Off page (MIDI1-5). Up to 32 trigger alternate groups can be setup on your DTX-MULTI 12. If there is no need for a pad to be assigned to a trigger alternate group, you can set this parameter to "off". Settings off or 1 to 32 NOTE • If no note numbers have been assigned to any of the pad's layers (A to D) on the MIDI Note page (MIDI1-2), this setting will be displayed as "--" and modification will not be possible. • MIDI Note Off messages are not sent when "off" has been set on the Receive Key-Off page (MIDI1-5). If you want to use trigger alternate groups, therefore, be sure to set this parameter to "on". This will ensure that Note Off messages are sent to prevent overlapping voices. Parameter-Setting Pages for "CC" Messages MIDI1-1 Control Change Number & Value page MIDI1-1≥-º¡- 1 CCNo=≥7/Val=VARI 2 3 1 Pad number Settings 01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW, HHCL, or HHSP B Control change number (CCNo) Use this parameter to set the type of MIDI Control Change message to be sent whenever the pad indicated by 1 is struck. Settings 1 to 95 C Control change value (Val) Use this parameter to set a value for the MIDI Control Change message to be sent whenever the pad indicated by 1 is struck. • VARI .........The control change value will depend on how hard the pad is struck. • 0 - 127 ......Control change messages are sent with this fixed value, regardless of how hard or soft the pad is struck. Settings VARI or 0 to 127 NOTE • Before setting Val 3 to "VARI", it will be necessary to access the Trigger Velocity page (MIDI1-7) with Message Type=note (MIDI1) and to set the TrgVel parameter to "variable". MIDI1-2 MIDI Channel page MIDI1-2≥-º¡- 1 ≥≥≥MIDI≥Ch=10 2 1 Pad number Settings 01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW, HHCL, or HHSP B MIDI channel (MIDI Ch) Use this parameter to set a MIDI channel for the Control Change messages to be sent whenever the pad indicated by 1 is struck. Settings 1 to 16 MIDI WAVE PATTERN UTILITY TRIGGER Owner's Manual 65