Yamaha DTX-MULTI Owner's Manual - Page 87

Gain, Frequency & Bandwidth, EQ Shape Master EQ Bypass Frequency band, Gain G

Get Yamaha DTX-MULTI PDF manuals and user guides View all Yamaha DTX-MULTI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Reference KIT VOICE UTILITY Setting Area (UTIL) UTIL3-1 Gain, Frequency & Bandwidth page UTIL3-1 mid 1 G+12/F2.0k/Q≥0.1 2 3 4 1 Frequency band Use this parameter to select the master-EQ frequency band to be set. Settings low, lowMid, mid, highMid, or high B Gain (G) Use this parameter to specify the amount by which the signal level in the frequency band indicated by 1 will be boosted or cut. Settings -12 to +0 to +12 C Frequency (F) Use this parameter to specify the frequency within the band indicated by 1 around which the signal level will be cut or boosted. If the "low" band has been selected, the range of available frequencies will depend on the EQ type set using the Shape parameter on the EQ Shape page (UTIL3-2). Settings low: 32 to 2.0k for "shelving" 63 to 2.0k for "peaking" lowMid, mid, and highMid: 100 to 10k high: 500 to 16k D Bandwidth (Q) Use this parameter to specify a width for the band of frequencies to be boosted or cut. If you set a large value, a narrower band of frequencies will be affected and the tone will change markedly around the center frequency. If you set a smaller value, a wider band of frequencies will be affected and the tone will change gradually around the center frequency. Settings 0.1 to 12.0 + Q = 0.1 Q = 12.0 0 Frequency - F (Frequency) NOTE • When "low" or "high" is indicated by 1 and "shelving" has been set using the Shape parameter on the EQ Shape page (UTIL3-2), the setting for Bandwidth (Q) will be displayed as "---" and modification will not be possible. UTIL3-2 EQ Shape page On the EQ Shape page, you can set an EQ type for each of the "low" and "high" bands. UTIL3-2 low 1 ≥Shape=shelving 2 1 Frequency band Use this parameter to select the master-EQ frequency band to be set. Settings low or high B Shape Use this parameter to set an EQ type. Settings shelving or peaking ● shelving: Signals at all frequencies either above or below the specified frequency will be boosted or cut. EQ low EQ high G (Gain) G (Gain) + F (Frequency) + F (Frequency) 0 0 - - Frequency Frequency ● peaking: Signals within a band of frequencies around the specified frequency will be boosted or cut. + G (Gain) F (Frequency) 0 Frequency - UTIL3-3 Master EQ Bypass page UTIL3-3 ≥MEQ≥Bypass=off 1 1 Master EQ bypass (MEQBypass) Use this parameter to specify whether the master EQ will be bypassed ("on") or applied ("off"). Settings off or on MIDI WAVE PATTERN UTILITY TRIGGER Owner's Manual 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
TRIGGER
Reference
KIT
MIDI
VOICE
UTILITY
WAVE
PATTERN
UTILITY Setting Area (UTIL)
Owner’s Manual
87
1
Frequency band
Use this parameter to select the master-EQ frequency band to
be set.
B
Gain (G)
Use this parameter to specify the amount by which the signal
level in the frequency band indicated by
1
will be boosted or
cut.
C
Frequency (F)
Use this parameter to specify the frequency within the band
indicated by
1
around which the signal level will be cut or
boosted. If the “low” band has been selected, the range of
available frequencies will depend on the EQ type set using the
Shape parameter on the EQ Shape page (UTIL3-2).
D
Bandwidth (Q)
Use this parameter to specify a width for the band of frequen-
cies to be boosted or cut. If you set a large value, a narrower
band of frequencies will be affected and the tone will change
markedly around the center frequency. If you set a smaller
value, a wider band of frequencies will be affected and the
tone will change gradually around the center frequency.
•
When “low” or “high” is indicated by
1
and “shelving” has been set using
the Shape parameter on the EQ Shape page (UTIL3-2), the setting for
Bandwidth (Q) will be displayed as “---” and modification will not be possi-
ble.
On the EQ Shape page, you can set an EQ type for each of the
“low” and “high” bands.
1
Frequency band
Use this parameter to select the master-EQ frequency band to
be set.
B
Shape
Use this parameter to set an EQ type.
●
shelving:
Signals at all frequencies either above or below the specified
frequency will be boosted or cut.
●
peaking:
Signals within a band of frequencies around the specified fre-
quency will be boosted or cut.
1
Master EQ bypass (MEQBypass)
Use this parameter to specify whether the master EQ will be
bypassed (“on”) or applied (“off”).
UTIL3-1
Gain, Frequency & Bandwidth
page
Settings
low, lowMid, mid, highMid, or high
Settings
-12 to +0 to +12
Settings
low:
32 to 2.0k for “shelving”
63 to 2.0k for “peaking”
lowMid, mid, and highMid: 100 to 10k
high: 500 to 16k
Settings
0.1 to 12.0
UTIL3-1≥≥≥≥≥≥mid
G+12/F2.0k/Q≥0.1
1
2
4
3
–
+
0
Q = 0.1
Q = 12.0
F (Frequency)
Frequency
NOTE
UTIL3-2
EQ Shape page
Settings
low or high
Settings
shelving or peaking
UTIL3-3
Master EQ Bypass page
Settings
off or on
UTIL3-2≥≥≥≥≥≥low
≥Shape=shelving
1
2
–
+
0
–
+
0
EQ low
EQ high
G (Gain)
F (Frequency)
G (Gain)
F
(Frequency)
Frequency
Frequency
–
+
0
G (Gain)
F (Frequency)
Frequency
UTIL3-3
≥MEQ≥Bypass=off
1