Home » ZyXEL Manuals » Networking » ZyXEL NWA3560-N » Manual Viewer

ZyXEL NWA3560-N User Guide - Page 152

Configuration > Object > AP Profile > Add/Edit Profile continued

Get ZyXEL NWA3560-N PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 152 highlights

Chapter 12 AP Profile Table 53 Configuration > Object > AP Profile > Add/Edit Profile (continued) LABEL DESCRIPTION Enable A-MPDU Aggregation Select this to enable A-MPDU aggregation. Message Protocol Data Unit (MPDU) aggregation collects Ethernet frames along with their 802.11n headers and wraps them in a 802.11n MAC header. This method is useful for increasing bandwidth throughput in environments that are prone to high error rates. A-MPDU Limit Enter the maximum frame size to be aggregated. A-MPDU Subframe Enter the maximum number of frames to be aggregated each time. Enable AMSDU Aggregation Select this to enable A-MSDU aggregation. Mac Service Data Unit (MSDU) aggregation collects Ethernet frames without any of their 802.11n headers and wraps the header-less payload in a single 802.11n MAC header. This method is useful for increasing bandwidth throughput. It is also more efficient than AMPDU except in environments that are prone to high error rates. A-MSDU Limit Enter the maximum frame size to be aggregated. RTS/CTS Threshold Use RTS/CTS to reduce data collisions on the wireless network if you have wireless clients that are associated with the same AP but out of range of one another. When enabled, a wireless client sends an RTS (Request To Send) and then waits for a CTS (Clear To Send) before it transmits. This stops wireless clients from transmitting packets at the same time (and causing data collisions). Fragmentation Threshold Beacon Interval DTIM Output Power A wireless client sends an RTS for all packets larger than the number (of bytes) that you enter here. Set the RTS/CTS equal to or higher than the fragmentation threshold to turn RTS/CTS off. The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. Enter an even number between 256 and 2346. When a wirelessly networked device sends a beacon, it includes with it a beacon interval. This specifies the time period before the device sends the beacon again. The interval tells receiving devices on the network how long they can wait in low-power mode before waking up to handle the beacon. A high value helps save current consumption of the access point. Delivery Traffic Indication Message (DTIM) is the time period after which broadcast and multicast packets are transmitted to mobile clients in the Active Power Management mode. A high DTIM value can cause clients to lose connectivity with the network. This value can be set from 1 to 255. Set the output power of the AP in this field. If there is a high density of APs in an area, decrease the output power of the NWA5160N to reduce interference with other APs. Select one of the following 100%(Full Power), 50%, 25%, or 12.5%. See the product specifications for more information on your NWA3000-N series AP's output power. Note: Reducing the output power also reduces the NWA3000-N series AP's effective broadcast radius. 152 NWA3000-N Series User's Guide

Section	Page
NWA3000-N Series	1
About This User's Guide	3
Document Conventions	4
Safety Warnings	6
Table of Contents	7
User’s Guide	15
Introduction	17
1.1 Overview	17
1.2 Applications for the NWA3000-N series AP	18
1.2.1 Bridge / Repeater	18
1.2.2 AP + Bridge	22
1.2.3 MBSSID	22
1.3 Management Mode	23
1.4 Ways to Manage the NWA3000-N series AP	24
1.5 Good Habits for Managing the NWA3000-N series AP	25
1.6 Hardware Connections	26
1.7 LEDs	27
1.8 Starting and Stopping the NWA3000-N series AP	29
The Web Configurator	31
2.1 Overview	31
2.2 Access	32
2.3 The Main Screen	33
2.3.1 Title Bar	34
2.3.2 Navigation Panel	34
2.3.3 Warning Messages	38
2.3.4 Site Map	38
2.3.5 Object Reference	38
2.3.6 Tables and Lists	44
Configuration Basics	49
3.1 Overview	49
3.2 Object-based Configuration	49
3.3 Feature Configuration Overview	49
3.3.1 Feature	50
3.3.2 MGNT Mode	50
3.3.3 LAN Setting	50
3.3.4 Wireless	50
3.3.5 Device HA	51
3.4 Objects	51
3.4.1 User	51
3.4.2 AP Profile	52
3.4.3 MON Profile	52
3.5 System	52
3.5.1 WWW, SSH, TELNET, FTP, SNMP, and Auth. Server	52
3.5.2 Logs and Reports	53
3.5.3 File Manager	53
3.5.4 Diagnostics	53
3.5.5 Shutdown	53
Tutorials	55
4.1 Sample Network Setup	55
4.1.1 Set the Management Modes	56
4.1.2 Set the LAN IP Address and Management VLAN (vlan99)	57
4.1.3 Set Up Wireless User Authentication	58
4.1.4 Create the AP Profiles (staff, guest)	60
4.2 Rogue AP Detection	63
4.2.1 Rogue AP Containment	67
4.3 Load Balancing	69
4.4 Dynamic Channel Selection	70
Technical Reference	73
Dashboard	75
5.1 Overview	75
5.1.1 What You Can Do in this Chapter	75
5.2 Dashboard	76
5.2.1 CPU Usage	80
5.2.2 Memory Usage	81
Monitor	83
6.1 Overview	83
6.1.1 What You Can Do in this Chapter	83
6.2 What You Need to Know	83
6.3 LAN Status	84
6.3.1 LAN Status Graph	86
6.4 AP List	87
6.4.1 Station Count of AP	89
6.5 Radio List	89
6.5.1 AP Mode Radio Information	91
6.6 Station List	93
6.7 Rogue AP	94
6.8 Legacy Device Info	95
6.8.1 Legacy Device Info Add or Edit	96
6.9 View Log	96
6.10 View AP Log	100
Management Mode	103
7.1 Overview	103
7.2 About CAPWAP	103
7.2.1 CAPWAP Discovery and Management	104
7.2.2 Managed AP Finds the Controller	104
7.2.3 CAPWAP and IP Subnets	104
7.2.4 Notes on CAPWAP	105
7.3 The Management Mode Screen	105
LAN Setting	107
8.1 LAN Setting Overview	107
8.1.1 What You Can Do in this Chapter	107
8.1.2 What You Need to Know	107
8.2 LAN Setting	108
8.2.1 Add or Edit a DNS Setting	110
Wireless	111
9.1 Overview	111
9.1.1 What You Can Do in this Chapter	111
9.1.2 What You Need to Know	111
9.2 Controller	112
9.3 AP Management	113
9.3.1 Edit AP List	115
9.4 MON Mode	116
9.4.1 Add/Edit Rogue/Friendly List	118
9.5 Load Balancing	119
9.5.1 Disassociating and Delaying Connections	120
9.6 DCS	122
9.7 Technical Reference	124
Device HA	127
10.1 Overview	127
10.1.1 What You Can Do in this Chapter	127
10.1.2 What You Need to Know	128
10.1.3 Before You Begin	128
10.2 Device HA General	129
10.3 Active-Passive Mode	131
10.3.1 Edit Monitored Interface	134
10.4 Technical Reference	135
User	137
11.1 Overview	137
11.1.1 What You Can Do in this Chapter	137
11.1.2 What You Need To Know	137
11.2 User Summary	138
11.2.1 Add/Edit User	139
11.3 Setting	141
11.3.1 Edit User Authentication Timeout Settings	144
AP Profile	147
12.1 Overview	147
12.1.1 What You Can Do in this Chapter	147
12.1.2 What You Need To Know	147
12.2 Radio	149
12.2.1 Add/Edit Radio Profile	150
12.3 SSID	154
12.3.1 SSID List	154
12.3.2 Security List	158
12.3.3 MAC Filter List	161
MON Profile	165
13.1 Overview	165
13.1.1 What You Can Do in this Chapter	165
13.1.2 What You Need To Know	165
13.2 MON Profile	166
13.2.1 Add/Edit MON Profile	167
13.3 Technical Reference	168
Certificates	171
14.1 Overview	171
14.1.1 What You Can Do in this Chapter	171
14.1.2 What You Need to Know	171
14.1.3 Verifying a Certificate	173
14.2 My Certificates	175
14.2.1 Add My Certificates	177
14.2.2 Edit My Certificates	181
14.2.3 Import Certificates	184
14.3 Trusted Certificates	185
14.3.1 Edit Trusted Certificates	187
14.3.2 Import Trusted Certificates	190
14.4 Technical Reference	191
System	193
15.1 Overview	193
15.1.1 What You Can Do in this Chapter	193
15.2 Host Name	194
15.3 Date and Time	194
15.3.1 Pre-defined NTP Time Servers List	197
15.3.2 Time Server Synchronization	198
15.4 Console Speed	199
15.5 WWW Overview	200
15.5.1 Service Access Limitations	200
15.5.2 System Timeout	200
15.5.3 HTTPS	200
15.5.4 Configuring WWW Service Control	201
15.5.5 HTTPS Example	203
15.6 SSH	209
15.6.1 How SSH Works	210
15.6.2 SSH Implementation on the NWA3000-N series AP	211
15.6.3 Requirements for Using SSH	211
15.6.4 Configuring SSH	212
15.6.5 Examples of Secure Telnet Using SSH	213
15.7 Telnet	214
15.8 FTP	215
15.9 SNMP	217
15.9.1 Supported MIBs	218
15.9.2 SNMP Traps	218
15.9.3 Configuring SNMP	219
15.9.4 Adding or Editing an SNMPv3 User Profile	220
15.10 Internal RADIUS Server	221
15.10.1 Configuring the Internal RADIUS Server	222
15.10.2 Adding or Editing a Trusted AP Profile	224
15.11 Technical Reference	225
Log and Report	227
16.1 Overview	227
16.1.1 What You Can Do In this Chapter	227
16.2 Email Daily Report	227
16.3 Log Setting	229
16.3.1 Log Setting Summary	230
16.3.2 Edit Log Settings	232
16.3.3 Edit Remote Server	236
16.3.4 Active Log Summary	238
File Manager	241
17.1 Overview	241
17.1.1 What You Can Do in this Chapter	241
17.1.2 What you Need to Know	241
17.2 Configuration File	243
17.3 Firmware Package	248
17.4 Shell Script	249
Diagnostics	253
18.1 Overview	253
18.1.1 What You Can Do in this Chapter	253
18.2 Diagnostics	253
18.3 Packet Capture	254
18.3.1 Packet Capture Files	256
18.3.2 Example of Viewing a Packet Capture File	257
18.4 Wireless Frame Capture	258
18.4.1 Wireless Frame Capture Files	261
Reboot	263
19.1 Overview	263
19.1.1 What You Need To Know	263
19.2 Reboot	263
Shutdown	265
20.1 Overview	265
20.1.1 What You Need To Know	265
20.2 Shutdown	265
Troubleshooting	267
21.1 Overview	267
21.2 Power, Hardware Connections, and LEDs	267
21.3 NWA3000-N series AP Access and Login	268
21.4 Internet Access	270
21.5 Wireless AP Troubleshooting	272
21.6 Resetting the NWA3000-N series AP	277
21.7 Getting More Troubleshooting Help	278
Product Specifications	279
22.1 Wall-Mounting Instructions	282
Log Descriptions	285
Importing Certificates	305
Wireless LANs	319
Open Software Announcements	333
Legal Information	373

Match case Limit results 1 per page

Chapter 12 AP Profile

NWA3000-N Series User’s Guide

152

Enable A-MPDU

Aggregation

Select this to enable A-MPDU aggregation.

Message Protocol Data Unit (MPDU) aggregation collects Ethernet

frames along with their 802.11n headers and wraps them in a

802.11n MAC header. This method is useful for increasing bandwidth

throughput in environments that are prone to high error rates.

A-MPDU Limit

Enter the maximum frame size to be aggregated.

A-MPDU

Subframe

Enter the maximum number of frames to be aggregated each time.

Enable A-

MSDU

Aggregation

Select this to enable A-MSDU aggregation.

Mac Service Data Unit (MSDU) aggregation collects Ethernet frames

without any of their 802.11n headers and wraps the header-less

payload in a single 802.11n MAC header. This method is useful for

increasing bandwidth throughput. It is also more efficient than A-

MPDU except in environments that are prone to high error rates.

A-MSDU Limit

Enter the maximum frame size to be aggregated.

RTS/CTS

Threshold

Use RTS/CTS to reduce data collisions on the wireless network if you

have wireless clients that are associated with the same AP but out of

range of one another. When enabled, a wireless client sends an RTS

(Request To Send) and then waits for a CTS (Clear To Send) before it

transmits. This stops wireless clients from transmitting packets at the

same time (and causing data collisions).

A wireless client sends an RTS for all packets larger than the number

(of bytes) that you enter here. Set the RTS/CTS equal to or higher

than the fragmentation threshold to turn RTS/CTS off.

Fragmentation

Threshold

The threshold (number of bytes) for the fragmentation boundary for

directed messages. It is the maximum data fragment size that can be

sent. Enter an even number between

256

and

2346

Beacon

Interval

When a wirelessly networked device sends a beacon, it includes with

it a beacon interval. This specifies the time period before the device

sends the beacon again. The interval tells receiving devices on the

network how long they can wait in low-power mode before waking up

to handle the beacon. A high value helps save current consumption

of the access point.

DTIM

Delivery Traffic Indication Message (DTIM) is the time period after

which broadcast and multicast packets are transmitted to mobile

clients in the Active Power Management mode. A high DTIM value

can cause clients to lose connectivity with the network. This value

can be set from 1 to 255.

Output Power

Set the output power of the AP in this field. If there is a high density

of APs in an area, decrease the output power of the NWA5160N to

reduce interference with other APs. Select one of the following

100%(Full Power)

50%

25%

, or

12.5%

. See the product

specifications for more information on your NWA3000-N series AP’s

output power.

Note: Reducing the output power also reduces the NWA3000-N

series AP’s effective broadcast radius.

Table 53

Configuration > Object > AP Profile > Add/Edit Profile (continued)

LABEL

DESCRIPTION