Asus AP1720-E1 User Guide - Page 52

Removable components

Get Asus AP1720-E1 PDF manuals and user guides View all Asus AP1720-E1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

2.10 Removable components You may need to remove previously installed system components when installing or removing system devices, or when you need to replace defective components. This section tells how to remove the following components: 1. Chassis fan 2. HDD fans 3. SCSI backplanes 4. Power supply module 5. Floppy disk drive 6. Front I/O board 2.10.1 Chassis fan To remove the chassis fan: 1. Disconnect the 3-pin fan cable from the connector CHA_FAN1 on the motherboard. 2. Press the tabs on the outer corners of the system fan, then pull the fan out of the chassis. To re-install the chassis fan: 1. Firmly hold the chassis fan on the side with the tabs and position it into its slot, making sure that the four hooks underneath the fan match the corresponding holes on the rear panel. 2. Push the fan into the chassis until the four hooks lock securely into the holes on the rear panel. 3. Re-connect the 3-pin fan cable from the connector CHA_FAN1 on the motherboard. 2-36 Chapter 2: Hardware setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Chapter 2:
Hardware setup
2-36
2.10
Removable components
You may need to remove previously installed system components when
installing or removing system devices, or when you need to replace
defective components. This section tells how to remove the following
components:
1.
Chassis fan
4.
Power supply module
2.
HDD fans
5.
Floppy disk drive
3.
SCSI backplanes
6.
Front I/O board
2.10.1
Chassis fan
To remove the chassis fan:
1.
Disconnect the 3-pin fan cable
from the connector CHA_FAN1
on the motherboard.
2.
Press the tabs on the outer
corners of the system fan, then
pull the fan out of the chassis.
To re-install the chassis fan:
1.
Firmly hold the chassis fan on the
side with the tabs and position it
into its slot, making sure that the
four hooks underneath the fan
match the corresponding holes on
the rear panel.
2.
Push the fan into the chassis until
the four hooks lock securely into
the holes on the rear panel.
3.
Re-connect the 3-pin fan cable
from the connector CHA_FAN1 on the motherboard.