Asus Adaptec 2020 ZCR User Manual - Page 45

UnixWare and OpenUNIX, Installing the Driver When You Install UnixWare or OpenUNIX

Get Asus Adaptec 2020 ZCR PDF manuals and user guides View all Asus Adaptec 2020 ZCR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Installing the Driver UnixWare and OpenUNIX This section contains the following procedures: ■ Installing the Driver When You Install UnixWare or OpenUNIX ■ Installing the Driver in an Existing UnixWare or OpenUNIX System Note: Although the driver disk you create for UnixWare and OpenUNIX differ, the installation procedures for these operating systems are the same. Installing the Driver When You Install UnixWare or OpenUNIX To install the driver with the operating system during a fresh install: 1 Install and configure the controller and hard drives, as described in page 2-3. 2 Create the bootable array, as described on page 2-5. 3 Create the driver disk, as described on page 3-2. When finished, remove the driver disk. 4 Insert the Unix installation CD and start the operating system installation. 5 When you see the prompt, Choose One, insert the driver disk, select Install HBA diskette, and then press F10. The computer loads the driver from the driver disk, then the HBA screen is displayed. 6 Select Proceed with Installation, then press F10. 7 Complete the installation as appropriate. 8 When the installation is finished, remove the driver disk and restart the computer. Installing the Driver in an Existing UnixWare or OpenUNIX System To install the driver in an existing operating system: 1 Shut down the computer. Install and configure the controller and hard drives, as described in Chapter 2. 2 Create the driver disk, as described on page 3-2. When finished, remove the driver disk. 3-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
3-8
Installing the Driver
UnixWare and OpenUNIX
This section contains the following procedures:
■
Installing the Driver When You Install UnixWare or OpenUNIX
■
Installing the Driver in an Existing UnixWare or OpenUNIX System
Note:
Although the driver disk you create for UnixWare and
OpenUNIX differ, the installation procedures for these
operating systems are the same.
Installing the Driver When You Install UnixWare or OpenUNIX
To install the driver with the operating system during a fresh
install:
1
Install and configure the controller and hard drives, as
described in
page 2-3
.
2
Create the bootable array, as described on
page 2-5
.
3
Create the driver disk, as described on
page 3-2
. When finished,
remove the driver disk.
4
Insert the Unix installation CD and start the operating system
installation.
5
When you see the prompt,
Choose One
, insert the driver disk,
select
Install HBA diskette
, and then press
F10
.
The computer loads the driver from the driver disk, then the
HBA screen is displayed.
6
Select
Proceed with Installation
, then press
F10
.
7
Complete the installation as appropriate.
8
When the installation is finished, remove the driver disk and
restart the computer.
Installing the Driver in an Existing UnixWare or OpenUNIX System
To install the driver in an existing operating system:
1
Shut down the computer. Install and configure the controller
and hard drives, as described in
Chapter 2
.
2
Create the driver disk, as described on
page 3-2
. When finished,
remove the driver disk.