Asus Adaptec 2020 ZCR User Manual - Page 46

Installing the NetWare Driver, Installing the Driver When You Install NetWare

Get Asus Adaptec 2020 ZCR PDF manuals and user guides View all Asus Adaptec 2020 ZCR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Installing the Driver 3 Turn on the computer, then insert the driver disk. 4 To run the pkgadd utility, type pkgadd -d diskette1 and then press Enter. UNIX reads the disk and package information. 5 Press Enter. 6 Restart the computer. The system rebuilds the kernel automatically. 7 Add devices created on the RAID controller to the operating system. For details, refer to your OpenServer documentation. Installing the NetWare Driver This section contains the following procedures: ■ Installing the Driver When You Install NetWare on page 3-9 ■ Installing the Driver in an Existing NetWare System on page 3-10 ■ Loading NetWare Drivers During Server Restart on page 3-11 Installing the Driver When You Install NetWare To install the driver with the operating system during a fresh install: 1 Install and configure the controller and hard drives, as described in page 2-3. 2 Create the bootable array, as described on page 2-5. 3 Create the driver disk, as described on page 3-2. When finished, remove the driver disk. 4 Restart the computer, then press Ctrl+A when prompted to access the ARC utility. Use ARC to create the RAID. For details, see Using the Adaptec RAID Configuration (ARC) Utility on page 2-6. 5 Install and configure a secondary controller, if any. 6 Create the driver disk, as described on page 3-2. When finished, remove the driver disk. 7 Install the operating system according to the NetWare documentation. Verify that you have the aacraid.ham and aacraid.ddi files available on the driver disk created at the beginning of this chapter. 3-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
3-9
Installing the Driver
3
Turn on the computer, then insert the driver disk.
4
To run the
pkgadd
utility, type
pkgadd -d diskette1
and then
press
Enter
. UNIX reads the disk and package information.
5
Press
Enter
.
6
Restart the computer. The system rebuilds the kernel
automatically.
7
Add devices created on the RAID controller to the operating
system. For details, refer to your OpenServer documentation.
Installing the NetWare Driver
This section contains the following procedures:
■
Installing the Driver When You Install NetWare
on page 3-9
■
Installing the Driver in an Existing NetWare System
on page 3-10
■
Loading NetWare Drivers During Server Restart
on page 3-11
Installing the Driver When You Install NetWare
To install the driver with the operating system during a fresh
install:
1
Install and configure the controller and hard drives, as
described in
page 2-3
.
2
Create the bootable array, as described on
page 2-5
.
3
Create the driver disk, as described on
page 3-2
. When finished,
remove the driver disk.
4
Restart the computer, then press
Ctrl+A
when prompted to access
the ARC utility. Use ARC to create the RAID. For details, see
Using the Adaptec RAID Configuration (ARC) Utility
on page 2-6
.
5
Install and configure a secondary controller, if any.
6
Create the driver disk, as described on
page 3-2
. When finished,
remove the driver disk.
7
Install the operating system according to the NetWare
documentation. Verify that you have the
aacraid.ham
and
aacraid.ddi
files available on the driver disk created at the
beginning of this chapter.