Cisco 4948 Installation Guide - Page 67

Step 3, power supply completely out of the chassis. Set the power supply aside.

Get Cisco 4948 - Catalyst Switch PDF manuals and user guides
UPC - 746320908878
View all Cisco 4948 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supply Step 3 Step 4 Step 5 Disconnect the DC-input cables from the power supply terminal block in this order (See Figure 4-1, top view): 1. Positive (+) source DC cable from the positive (+) terminal 2. Negative (-) source DC cable from the negative (-) terminal 3. Ground cable from the ground terminal Loosen the captive installation screw on the power supply. Grasp the power supply handle with one hand, and slide the power supply halfway out of the chassis. Place your other hand underneath the power supply, as shown in Figure 4-1 (bottom view), and slide the power supply completely out of the chassis. Set the power supply aside. Note The DC power supply is equipped with an EMI gasket on the top and bottom (on the front edge) of the power supply. When sliding the power supply into or out of the power supply bay, be careful not to damage the EMI gaskets. Step 6 If the power supply bay is to remain empty, install a blank faceplate (WS-X4994) over the opening, and secure it in place with the captive installation screw. OL-21561-02 Catalyst 4948E and Catalyst 4948E-F Switch Installation Guide 4-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
4-3
Catalyst 4948E and Catalyst 4948E-F Switch Installation Guide
OL-21561-02
Chapter 4
Removal and Replacement Procedures
Removing and Installing the DC-Input Power Supply
Step 3
Disconnect the DC-input cables from the power supply terminal block in this order (See
Figure 4-1
, top
view):
1.
Positive (+) source DC cable from the positive (+) terminal
2.
Negative (–) source DC cable from the negative (–) terminal
3.
Ground cable from the ground terminal
Step 4
Loosen the captive installation screw on the power supply.
Step 5
Grasp the power supply handle with one hand, and slide the power supply halfway out of the chassis.
Place your other hand underneath the power supply, as shown in
Figure 4-1
(bottom view), and slide the
power supply completely out of the chassis. Set the power supply aside.
Note
The DC power supply is equipped with an EMI gasket on the top and bottom (on the front edge)
of the power supply. When sliding the power supply into or out of the power supply bay, be
careful not to damage the EMI gaskets.
Step 6
If the power supply bay is to remain empty, install a blank faceplate (WS-X4994) over the opening, and
secure it in place with the captive installation screw.