Craftsman #10402 Operation Manual - Page 58

Cause, Solution

Get Craftsman #10402 - Professional Laser 10 in. Radial Arm Saw 22010 PDF manuals and user guides View all Craftsman #10402 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

CAUSE SOLUTION Saw does not start. 1. Motor cord or controPcut cord is 1. PUugin cord, not pUugged in. 2. Cord or switch is damaged. 2. Have the cord or switch re- pUaced at your nearest Sears Service Center. 3. Circuit fuse is blown. 4. Circuit breaker is tripped. 5. Switch is burned out. 6. Connections are loose, burned out, or damaged, 3. Replace circuit fuse. 4. Reset circuit breaker. 5. Have the switch replaced and request a voltage check from the power company. 6. Have the wiring checked and repaired. Request voltage check Motor does not reach full speed or power, Motor stalls, blows fuses, or trips circuit breakers. Motor overheats. 1. Voltage from source is low. 2. Circuit is overloaded with other appliances or motors, 3. Motor windings are burned out. 4. Fuses or circuit breakers are wrong size. 5. Extension cord is too long. 6. Starter switch is defective. 1. Starter switch is defective. 2. Voltage from source is low. 3. Fuses or circuit breakers are wrong size or defective, 1. Motor is overloaded. 2. Windings are burned out. 3. Work is being fed too fast. 1. Request a voltage check from the power company. 2. Test without any other motors and on different circuit. 3. Have the windings replaced and request a voltage check from the power company. 4. Have an electrician replace with a 15 amp fuse or circuit breaker. 5. Use a shorter cord. 6. Have the switch replaced. 1. Have the switch replaced. 2. Request a voltage check from the power company. 3. Have an electrician replace with a 15 amp fuse or circuit breaker. 1. Request a voltage check from the power company. 2. Have the windings replaced and request a voltage check from the power company. 3. Feed work slower. _RRFTSMRN'RADIAL SAW 315.220100 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
CAUSE
SOLUTION
Saw does not start.
1. Motor cord or controPcut
cord is
1. PUugin cord,
not pUugged in.
2.
Cord or switch is damaged.
2.
Have the cord or switch re-
pUaced at your nearest Sears
Service Center.
3.
Circuit fuse is blown.
3.
Replace circuit fuse.
4.
Circuit breaker is tripped.
4.
Reset circuit
breaker.
5.
Switch is burned out.
5.
Have the switch replaced and
request a voltage
check from
the power company.
6.
Connections
are loose, burned
6.
Have the wiring checked and
out, or damaged,
repaired.
Request voltage check
Motor does not reach full speed or
1. Voltage from source
is low.
1. Request a voltage
check from
power,
the power company.
2.
Circuit is overloaded
with other
2. Test without any other motors
appliances
or motors,
and on different circuit.
3.
Motor windings
are burned out.
3.
Have the windings
replaced and
request a voltage
check from
the power company.
4.
Fuses or circuit
breakers
are
4.
Have an electrician
replace with
wrong
size.
a 15 amp fuse or circuit
breaker.
5.
Extension
cord is too long.
5.
Use a shorter
cord.
6.
Starter switch
is defective.
6.
Have the switch replaced.
Motor stalls, blows fuses, or trips
1. Starter switch
is defective.
1. Have the switch replaced.
circuit
breakers.
2. Voltage from source
is low.
2.
Request a voltage
check from
the power company.
3.
Fuses or circuit
breakers
are
3.
Have an electrician
replace with
wrong
size or defective,
a 15 amp fuse or circuit
breaker.
Motor overheats.
1. Motor is overloaded.
1. Request a voltage
check from
the power company.
2. Windings
are burned out.
2.
Have the windings
replaced and
request a voltage
check from
the power company.
3. Work is being fed too fast.
3.
Feed work slower.
_RRFTSMRN'RADIAL SAW 315.220100
58