Craftsman #10402 Operation Manual - Page 60

Yoke Clamp

Get Craftsman #10402 - Professional Laser 10 in. Radial Arm Saw 22010 PDF manuals and user guides View all Craftsman #10402 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

HandwheeU is hard to turn or column binds, Saw burns or scores edges of wood in cut. Bevel cuts are not true. CAUSE SOLUTION 1_ Sawdust has collected on the elevating shafL 2_ Column is out of aHgnmenL 1_ Column tube is too Uoose in the column support. 2. Blade or teeth are bent or dull. 3. Blade is out of alignment. 4. Wrong blade is being used. 5. Board is warped. 6. Arm is loose or misaligned. 7. Yoke is loose on carriage. 8. Arm is out of alignment. 9. Work is being fed too fast. 1. Bevel lock lever is loose. 2. Blade is not perpendicular to table top. 3. Column tube is too loose in the column support. 4. Table top is not parallel to the arm. 5. Yoke is loose on carriage. 6. Arm is out of alignment. 1_ Remove handwheeU; clean and Uubricate the shafL 2_ See Adjusting the Column Tube in Assembly section, 1_ See Adjusting the Column Tube in Assembly section, 2. Sharpen or replace the blade. See the removal procedure in Assembly section. 3. Use blade alignment procedures in Adjustment section. 4. Change blade. See the removal procedure in Assembly section. 5. Replace the board. 6. See Setting the Arm Lock V_Zheeiln the Assembly section. 7. See Setting the 'Yoke Clamp procedure in Assembly section. 8. See Aligning Arm for Cross Cuts in Adjustments section. 9. Feed work into blade slower. 1. See Setting the Bevel Lock Lever in Assembly section. 2. See Aligning the Blade to the Table in Adjustments section. 3. See Adjusting the Column Tube in Assembly section. 4. See Leveling Table Supports and Leveling the Front Table in the Assembly section. 5. See Setting the Yoke Clamp procedure in Assembly section. 6. See Aligning Arm for Cross Cuts in Adjustments section. _RRFTSMRN RADIAL SAW 315.220100 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
CAUSE
SOLUTION
HandwheeU is hard to turn or
1_ Sawdust
has collected
on the
1_ Remove
handwheeU; clean and
column
binds,
elevating
shafL
Uubricate the shafL
2_ Column
is out of aHgnmenL
2_ See
Adjusting
the Column
Tube
in
Assembly
section,
Saw burns or scores
edges of
1_ Column tube is too Uoosein the
1_ See
Adjusting
the Column
wood in cut.
column support.
Tube
in
Assembly
section,
2.
Blade or teeth are bent or dull.
2. Sharpen
or replace the blade.
See the removal
procedure
in
Assembly
section.
3.
Blade is out of alignment.
3.
Use blade alignment
proce-
dures in
Adjustment
section.
4. Wrong
blade is being used.
4. Change
blade. See the removal
procedure
in
Assembly
section.
5.
Board is warped.
5.
Replace the board.
6. Arm is loose or misaligned.
6. See
Setting
the Arm Lock
V_Zheel
in the
Assembly
section.
7. Yoke is loose on carriage.
7. See
Setting
the
'Yoke Clamp
procedure
in
Assembly
section.
8.
Arm is out of alignment.
8.
See
Aligning
Arm for
Cross
Cuts
in
Adjustments
section.
9.
Work is being fed too fast.
9.
Feed work into blade slower.
Bevel cuts are not true.
1.
Bevel lock lever is loose.
1. See
Setting
the Bevel Lock
Lever
in
Assembly
section.
2.
Blade is not perpendicular
to
2. See
Aligning
the Blade to the
table top.
Table
in
Adjustments
section.
3.
Column tube is too loose in the
3.
See
Adjusting
the
Column
column support.
Tube
in
Assembly
section.
4. Table top is not parallel to the
4. See
Leveling
Table Supports
arm.
and
Leveling
the Front Table
in
the
Assembly
section.
5. Yoke is loose on carriage.
5. See
Setting
the Yoke Clamp
procedure
in
Assembly
section.
6. Arm is out of alignment.
6. See
Aligning
Arm for Cross
Cuts
in
Adjustments
section.
_RRFTSMRN RADIAL SAW 315.220100
60