Craftsman #10402 Operation Manual - Page 59

Assembly, Installing, Assem, Adjustment, Adjusting, Setting, the Arm Lock, the Yoke

Get Craftsman #10402 - Professional Laser 10 in. Radial Arm Saw 22010 PDF manuals and user guides View all Craftsman #10402 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

PROBLEM CAUSE SOLUTION Saw vibrates excessiveUy. Saw is noisy when running, Carriage does not travel smoothly in track under arm. Saw stalls when ripping. 1. BUade is warped, 2. Saw is not mounted secureUy. 3. Work surface is uneven, 1. Motor needs attention, 1. Track is dirty or sticky. 2. Carriage bearings are bad. 3. Blade or teeth are dull or bent. 4. Blade is out of alignment. 5. Board is warped. 1. Blade or teeth are dull or bent. 2. Fence is not straight. 3. Work is being fed too fast. 4. Wrong blade is being used. 5. Column tube is too loose in the column support. 6. Arm is misaligned or loose. 7. Yoke is loose on carriage. 8. Sawdust has accumulated between tables. 1. RepUace the Made, See the removaU procedure in Assembly section, 2. Tighten aH hardware, 3. Reposifion on a fiat surface, Adjust the bveHng feet on bgs. 1. Have the motor checked at your nearest Sears Service Center. 1. Clean track. See Installing Carriage Assembly in Assembfy section. 2. Replace carriage bearings. Contact your nearest Sears service center, 3. Sharpen or replace the blade. See the removal procedure in Assembly section. 4. Use blade alignment procedures in Adjustment section. 5. Replace the board. 1. Sharpen or replace the blade. See the removal procedure in Assembly section. 2. Check with square; sand or replace. 3. Feed work into blade slower. 4. Change the blade. 5. See Adjusting the Column Tube in Assembly section. 6. See Setting the Arm Lock HZhee/in the Assembly section. 7. See Setting the Yoke Clamp procedure in Assembly section. 8. Remove and clean tables. 59 CRRFTSMANRADIAL SAW315.220100

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
PROBLEM
CAUSE
SOLUTION
Saw vibrates excessiveUy.
1. BUade is warped,
1.
RepUace the Made, See the
removaU procedure
in
Assembly
section,
2. Saw is not mounted secureUy.
2. Tighten
aH hardware,
3.
Work surface
is uneven,
3.
Reposifion on a fiat surface,
Adjust the bveHng feet on bgs.
Saw is noisy when running,
1. Motor needs attention,
1.
Have the motor checked at
your nearest Sears Service
Center.
Carriage
does not travel smoothly
1. Track is dirty or sticky.
1. Clean track. See
Installing
in track under arm.
Carriage
Assembly
in
Assem-
bfy
section.
2. Carriage
bearings are bad.
2.
Replace carriage bearings.
Contact
your nearest
Sears
service
center,
3.
Blade or teeth are dull or bent.
3.
Sharpen
or replace the blade.
See the removal
procedure
in
Assembly
section.
4. Blade is out of alignment.
4.
Use blade alignment
proce-
dures in
Adjustment
section.
5. Board is warped.
5.
Replace the board.
Saw stalls when ripping.
1. Blade or teeth are dull or bent.
1. Sharpen
or replace the blade.
See the removal
procedure
in
Assembly
section.
2. Fence is not straight.
2. Check with square;
sand or
replace.
3.
Work is being fed too fast.
3.
Feed work into blade slower.
4. Wrong
blade is being used.
4. Change the blade.
5. Column
tube is too loose in the
5. See
Adjusting
the
Column
column support.
Tube
in
Assembly
section.
6. Arm is misaligned
or loose.
6. See
Setting
the Arm Lock
HZhee/in the
Assembly
section.
7. Yoke is loose on carriage.
7. See
Setting
the Yoke
Clamp
procedure
in
Assembly
section.
8.
Sawdust
has accumulated
8.
Remove and clean tables.
between
tables.
59
CRRFTSMANRADIALSAW315.220100