D-Link DES-3010F Reference Manual - Page 103

Link Aggregation Commands, create link_aggregation

Get D-Link DES-3010F PDF manuals and user guides View all D-Link DES-3010F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

DES-30XX Layer 2 Switch CLI Reference Manual 17 LINK AGGREGATION COMMANDS The link aggregation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create link_aggregation group_id {type [lacp | static]} delete link_aggregation group_id config link_aggregation group_id {master_port | ports | state [enable | disable]} config link_aggregation [mac_source | mac_destination | mac_source_dest] algorithm show link_aggregation {group_id | algorithm} config lacp_port mode [active | passive] show lacp_port {} Each command is listed, in detail, in the following sections. create link_aggregation Purpose Used to create a link aggregation group on the Switch. Syntax create link_aggregation group_id {type [lacp | static]} Description This command will create a link aggregation group with a unique identifier. Parameters − Specifies the group ID. The Switch allows up to 3 link aggregation groups to be configured. The group number identifies each of the groups. group_id 3 is designed for the uplink modules only (the last two ports on the Switch (9-10, 17-18, 25-26) and can only be configured for them. type - Specify the type of link aggregation used for the group. If the type is not specified the default type is static. lacp - This designates the port group as LACP compliant. LACP allows dynamic adjustment to the aggregated port group. LACP compliant ports may be further configured (see config lacp_ports). LACP compliant must be connected to LACP compliant devices. static - This designates the aggregated port group as static. Static port groups can not be changed as easily as LACP compliant port groups since both linked devices must be manually configured if the configuration of the trunked group is changed. If static link aggregation is used, be sure that both ends of the connection are properly configured and that all ports have the same speed/duplex settings. Restrictions Only administrator-level users can issue this command. Example usage: To create a link aggregation group: 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
DES-30XX Layer 2 Switch CLI Reference Manual
99
17
L
INK
A
GGREGATION
C
OMMANDS
The link aggregation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.
Command
Parameters
create link_aggregation
group_id <value 1-3> {type [lacp | static]}
delete link_aggregation
group_id <value 1-3>
config link_aggregation
group_id <value 1-3> {master_port <port> | ports <portlist> | state
[enable | disable]}
config link_aggregation
algorithm
[mac_source | mac_destination | mac_source_dest]
show link_aggregation
{group_id <value 1-3> | algorithm}
config lacp_port
<portlist> mode [active | passive]
show lacp_port
{<portlist>}
Each command is listed, in detail, in the following sections.
create link_aggregation
Purpose
Used to create a link aggregation group on the Switch.
Syntax
create link_aggregation group_id <value 1-3>
{type [lacp | static]}
Description
This command will create a link aggregation group with a unique identifier.
Parameters
<value 1-3>
−
Specifies the group ID. The Switch allows up to 3 link
aggregation groups to be configured. The group number identifies each of
the groups.
group_id 3
is designed for the uplink modules only (the last two
ports on the Switch (9-10, 17-18, 25-26) and can only be configured for
them.
type
– Specify the type of link aggregation used for the group. If the type is
not specified the default type is static.
±
lacp
– This designates the port group as LACP compliant. LACP
allows dynamic adjustment to the aggregated port group. LACP
compliant ports may be further configured (see config lacp_ports).
LACP compliant must be connected to LACP compliant devices.
±
static
– This designates the aggregated port group as static. Static
port groups can not be changed as easily as LACP compliant port
groups since both linked devices must be manually configured if the
configuration of the trunked group is changed. If static link aggregation
is used, be sure that both ends of the connection are properly
configured and that all ports have the same speed/duplex settings.
Restrictions
Only administrator-level users can issue this command.
Example usage:
To create a link aggregation group: