D-Link DES-3010F Reference Manual - Page 111

config igmp_snooping, Last Member Query Timer when an IGMP Leave Report Packet is received

Get D-Link DES-3010F PDF manuals and user guides View all D-Link DES-3010F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

DES-30XX Layer 2 Switch CLI Reference Manual config igmp_snooping fast leave function. Enabled, this function will allow members of a multicast group to leave the group immediately (without the implementation of the Last Member Query Timer) when an IGMP Leave Report Packet is received by the Switch. Restrictions Only administrator-level users can issue this command. Example usage: To configure the igmp snooping: DES-3026:4#config igmp_snooping vlan_name default host_timeout 250 state enabled Command: config igmp_snooping vlan_name default host_timeout 250 state enabled Success. DES-3026:4# config igmp_snooping querier Purpose Used to configure the time in seconds between general query transmissions, the maximum time in seconds to wait for reports from members and the permitted packet loss that guarantees IGMP snooping. Syntax config igmp_snooping querier [vlan_name | all] {query_interval | max_response_time | robustness_variable | last_member_query_interval | state [enable | disable]} Description This command configures IGMP snooping querier. Parameters vlan_name − The name of the VLAN for which IGMP snooping querier is to be configured. all - Selecting this parameter will configure IGMP for all VLANs on the Switch. query_interval − Specifies the amount of time in seconds between general query transmissions. The default setting is 125 seconds. max_response_time − Specifies the maximum time in seconds to wait for reports from members. The default setting is 10 seconds. robustness_variable − Provides fine-tuning to allow for expected packet loss on a subnet. The value of the robustness variable is used in calculating the following IGMP message intervals: • Group member interval-Amount of time that must pass before a multicast router decides there are no more members of a group on a network. This interval is calculated as follows: (robustness variable x query interval) + (1 x query response interval). • Other querier present interval-Amount of time that must pass before a multicast router decides that there is no longer another multicast router that is the querier. This interval is calculated as follows: (robustness variable x query interval) + (0.5 x query response interval). • Last member query count-Number of group-specific queries sent before the router assumes there are no local members of a group. 107

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
DES-30XX Layer 2 Switch CLI Reference Manual
107
config igmp_snooping
fast leave
function. Enabled, this function will allow members of a multicast
group to leave the group immediately (without the implementation of the
Last Member Query Timer) when an IGMP Leave Report Packet is received
by the Switch.
Restrictions
Only administrator-level users can issue this command.
Example usage:
To configure the igmp snooping:
DES-3026:4#config igmp_snooping vlan_name default host_timeout 250
state enabled
Command: config igmp_snooping vlan_name default host_timeout 250
state enabled
Success.
DES-3026:4#
config igmp_snooping querier
Purpose
Used to configure the time in seconds between general query
transmissions, the maximum time in seconds to wait for reports from
members and the permitted packet loss that guarantees IGMP snooping.
Syntax
config igmp_snooping querier [vlan_name <vlan_name 32> | all]
{query_interval <sec 1-65535> | max_response_time <sec 1-25> |
robustness_variable <value 1-255> | last_member_query_interval <sec
1-25> | state [enable | disable]}
Description
This command configures IGMP snooping querier.
Parameters
vlan_name <vlan_name 32>
−
The name of the VLAN for which IGMP
snooping querier is to be configured.
all
– Selecting this parameter will configure IGMP for all VLANs on the
Switch.
query_interval <sec 1-65535>
−
Specifies the amount of time in seconds
between general query transmissions. The default setting is 125 seconds.
max_response_time <sec 1-25>
−
Specifies the maximum time in seconds
to wait for reports from members. The default setting is 10 seconds.
robustness_variable <value 1-255>
−
Provides fine-tuning to allow for
expected packet loss on a subnet. The value of the robustness variable is
used in calculating the following IGMP message intervals:
•
Group member interval—Amount of time that must pass before a
multicast router decides there are no more members of a group on
a network. This interval is calculated as follows: (robustness
variable x query interval) + (1 x query response interval).
•
Other querier present interval—Amount of time that must pass
before a multicast router decides that there is no longer another
multicast router that is the querier. This interval is calculated as
follows: (robustness variable x query interval) + (0.5 x query
response interval).
•
Last member query count—Number of group-specific queries sent
before the router assumes there are no local members of a group.