D-Link DES-3010F Reference Manual - Page 27

config ports, show ports - d link

Page 27 highlights

DES-30XX Layer 2 Switch CLI Reference Manual config ports state [enable | disable] − Enables or disables the specified range of ports. description - Enter an alphanumeric string of no more than 32 characters to describe a selected port interface. clear_description - Enter this command to clear the port description of the selected port(s). Restrictions Only administrator-level users can issue this command. Example usage: To configure the speed of ports 1-3 to be 10 Mbps, full duplex and state enabled: DES-3026:4#config ports 1-3 speed 10_full state enable Command: config ports 1-3 speed 10_full state enable Success. DES-3026:4# show ports Purpose Syntax Description Parameters Restrictions Used to display the current configuration of a range of ports. show ports {} {[description | err_disabled]} This command is used to display the current configuration of a range of ports. − Specifies a port or range of ports to be displayed. description - Adding this parameter to the command will allow the user to view previously configured descriptions set on various ports on the Switch. err_disabled - Used to view information about ports that have had their connection status disabled, for reasons such as STP loopback detection or link down status. None. Example usage: To display the configuration of ports 1-5 on the Switch: DES-3026:4#show ports 1-5 Command: show ports 1-5 Port Port Settings Connection Address State Speed/Duplex/FlowCtrl Speed/Duplex/FlowCtrl Learning -------- 1 Enabled Auto/Enabled 100/Full/none Enabled 2 Enabled Auto/Enabled Link Down Enabled 3 Enabled Auto/Enabled Link Down Enabled 4 Enabled Auto/Enabled Link Down Enabled 5 Enabled Auto/Enabled Link Down Enabled CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174

DES-30XX Layer 2 Switch CLI Reference Manual
23
config ports
state [enable | disable]
Enables or disables the specified range of ports.
description <desc 32>
- Enter an alphanumeric string of no more than 32
characters to describe a selected port interface.
clear_description
– Enter this command to clear the port description of the
selected port(s).
Restrictions
Only administrator-level users can issue this command.
Example usage:
To configure the speed of ports 1-3 to be 10 Mbps, full duplex and state enabled:
DES-3026:4#config ports 1-3 speed 10_full state enable
Command: config ports 1-3 speed 10_full state enable
Success.
DES-3026:4#
show ports
Purpose
Used to display the current configuration of a range of ports.
Syntax
show ports {<portlist>} {[description | err_disabled]}
Description
This command is used to display the current configuration of a range
of ports.
Parameters
<portlist>
Specifies a port or range of ports to be displayed.
description
– Adding this parameter to the command will allow the
user to view previously configured descriptions set on various ports
on the Switch.
err_disabled
– Used to view information about ports that have had
their connection status disabled, for reasons such as STP loopback
detection or link down status.
Restrictions
None.
Example usage:
To display the configuration of ports 1-5 on the Switch:
DES-3026:4#show ports 1-5
Command: show ports 1-5
Port
Port
Settings
Connection
Address
State
Speed/Duplex/FlowCtrl
Speed/Duplex/FlowCtrl
Learning
---
--------
---------------------
---------------------
--------
1
Enabled
Auto/Enabled
100/Full/none
Enabled
2
Enabled
Auto/Enabled
Link Down
Enabled
3
Enabled
Auto/Enabled
Link Down
Enabled
4
Enabled
Auto/Enabled
Link Down
Enabled
5
Enabled
Auto/Enabled
Link Down
Enabled
CTRL+C ESC q Quit SPACE n Next Page p Previous Page r Refresh