D-Link DIR-506L SharePort Go User Manual - Page 58

Routing, changes, click - specification

Get D-Link DIR-506L PDF manuals and user guides View all D-Link DIR-506L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Section 3 - Configuration Routing The Routing option is an advanced method of customizing specific routes of data through your network. After making your changes, click the Save Settings button. Note this option is only available in Router mode. RIP: Select Enable to turn on routing and auto-select the RIP version, or select RIPv1 or RIPv2. Destination IP: Enter the IP address of packets that will take this route. Subnet Mask: Enter the subnet mask of the route. Please note that the octets must match your destination IP address. Gateway: Enter your next hop gateway to be taken if this route is used. Hop: Enter a number to represent the hop value of this route. Enable: Check to enable this route or leave unchecked to ignore it. D-Link DIR-506L User Manual 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
54
D-Link DIR-506L User Manual
Section 3 - Configuration
Select
Enable
to turn on routing and auto-select the RIP
version, or select
RIPv1
or
RIPv2
.
Enter the IP address of packets that will take this route.
Enter the subnet mask of the route. Please note that the
octets must match your destination IP address.
Enter your next hop gateway to be taken if this route is
used.
Enter a number to represent the hop value of this route.
Check to enable this route or leave unchecked to ignore it.
RIP:
Destination IP:
Subnet Mask:
Gateway:
Hop:
Enable:
Routing
The
Routing
option is an advanced method of customizing specific routes of data through your network. After making your
changes, click the
Save Settings
button. Note this option is only available in Router mode.