Dell Inspiron 14 5410 2-in-1 Service Manual - Page 42

Power-adapter port, Removing the power-adapter port

Get Dell Inspiron 14 5410 2-in-1 PDF manuals and user guides View all Dell Inspiron 14 5410 2-in-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Steps 1. Slide the display assembly at an angle, and place the display assembly on the palm-rest and keyboard assembly. 2. Replace the four screws (M2.5x3.5) that secure the display hinges to the palm-rest and keyboard assembly. 3. Route the display cable through the routing guide on the palm-rest and keyboard assembly. 4. Slide the display cable into the connector on the system board and close the latch to secure the cable. 5. Connect the display-cable connector to the system board and close the latch to secure the cable. 6. Adhere the tape that secures the display cable to the system board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. 3. Exit Service Mode. Power-adapter port Removing the power-adapter port Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. 4. Remove the display assembly. About this task The following image indicates the location of the power-adapter port and provides a visual representation of the removal procedure. Steps 1. Disconnect the power-adapter port cable from the system board. 2. Peel the tape that secures the power-adapter port cable to the system board. 42 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Steps
1.
Slide the display assembly at an angle, and place the display assembly on the palm-rest and keyboard assembly.
2.
Replace the four screws (M2.5x3.5) that secure the display hinges to the palm-rest and keyboard assembly.
3.
Route the display cable through the routing guide on the palm-rest and keyboard assembly.
4.
Slide the display cable into the connector on the system board and close the latch to secure the cable.
5.
Connect the display-cable connector to the system board and close the latch to secure the cable.
6.
Adhere the tape that secures the display cable to the system board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
3.
Exit
Service Mode
.
Power-adapter port
Removing the power-adapter port
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Enter
Service Mode
.
3.
Remove the
base cover
.
4.
Remove the
display assembly
.
About this task
The following image indicates the location of the power-adapter port and provides a visual representation of the removal
procedure.
Steps
1.
Disconnect the power-adapter port cable from the system board.
2.
Peel the tape that secures the power-adapter port cable to the system board.
42
Removing and installing components