Dell Inspiron 14 5410 2-in-1 Service Manual - Page 48

Installing the I/O board

Get Dell Inspiron 14 5410 2-in-1 PDF manuals and user guides View all Dell Inspiron 14 5410 2-in-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Steps 1. Remove the two screws (M2.5x3.5) that secure the right display hinge to the I/O board and palm-rest and keyboard assembly. 2. Open the right display hinge at an angle of 90 degrees. 3. Peel the tape that secures the I/O-board cable to the I/O board. 4. Open the latch, and disconnect the I/O-board cable from the I/O board. 5. Open the latch, and disconnect the fingerprint reader-cable from the I/O board. 6. Disconnect the coin-cell battery cable from the I/O board. 7. Remove the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly. 8. Slide and lift the I/O board off the palm-rest and keyboard assembly. Installing the I/O board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the I/O board and provides a visual representation of the installation procedure. 48 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Steps
1.
Remove the two screws (M2.5x3.5) that secure the right display hinge to the I/O board and palm-rest and keyboard
assembly.
2.
Open the right display hinge at an angle of 90 degrees.
3.
Peel the tape that secures the I/O-board cable to the I/O board.
4.
Open the latch, and disconnect the I/O-board cable from the I/O board.
5.
Open the latch, and disconnect the fingerprint reader-cable from the I/O board.
6.
Disconnect the coin-cell battery cable from the I/O board.
7.
Remove the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.
8.
Slide and lift the I/O board off the palm-rest and keyboard assembly.
Installing the I/O board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the I/O board and provides a visual representation of the installation procedure.
48
Removing and installing components