Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 46

Installing a cooling fan, Drives, Removing a drive blank

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Next steps 1. Replace the cooling fan or install the cooling fan blank. 2. Replace the air shroud. Installing a cooling fan Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. 4. If installed, remove the cooling fan blank. Steps 1. Lower the cooling fan into the fan cage. 2. Press the release tabs on the fan cable connector and connect the cable to the system board. NOTE: Route the cable properly to prevent the cable from being pinched or crimped. Figure 22. Installing a fan Next steps 1. Install the air shroud. 2. Follow the procedure listed in the After working inside your system. Drives Removing a drive blank Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. If installed, remove the front bezel. CAUTION: To maintain proper system cooling, drive blanks must be installed in all empty drive slots. CAUTION: Mixing drive blanks from previous generations of PowerEdge servers is not supported. 46 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Next steps
1.
Replace the cooling fan
or
install the cooling fan blank
.
2.
Replace the air shroud
.
Installing a cooling fan
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud
.
4.
If installed,
remove the cooling fan blank
.
Steps
1.
Lower the cooling fan into the fan cage.
2.
Press the release tabs on the fan cable connector and connect the cable to the system board.
NOTE:
Route the cable properly to prevent the cable from being pinched or crimped.
Figure 22. Installing a fan
Next steps
1.
Install the air shroud
.
2.
Follow the procedure listed in the
After working inside your system
.
Drives
Removing a drive blank
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
If installed,
remove the front bezel
.
CAUTION:
To maintain proper system cooling, drive blanks must be installed in all empty drive slots.
CAUTION:
Mixing drive blanks from previous generations of PowerEdge servers is not supported.
46
Installing and removing system components