Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 91

Installing the system board

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Next steps 1. Replace the system board. Installing the system board Prerequisites NOTE: Before replacing the system board, replace the old iDRAC MAC address label in the Information tag with the iDRAC MAC address label of the replacement system board. 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. If you are replacing the system board, remove all the components that are listed in the removing the system board section. Steps 1. Unpack the new system board assembly. NOTE: Do not lift the system board by holding a memory module, processor, or other components. CAUTION: Take care not to damage the system identification button while placing the system board into the chassis. 2. Holding the system board holder, lower the system board it into the system. 3. Incline the system board at an angle and align the connectors with the slots on the rear of the chassis. 4. Slide the system board towards the rear of the chassis until the connectors are firmly seated in the slots. Figure 76. Installing the system board 5. Using a Phillips #2 screwdriver, fasten the screws that secure the system board to the chassis. Next steps 1. Replace the following: a. Trusted platform module NOTE: The TPM Module must be replaced only while installing new system board. b. Internal dual SD module, if applicable c. Heat sink and processor d. If applicable, Storage controller card Installing and removing system components 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Next steps
1.
Replace the system board
.
Installing the system board
Prerequisites
NOTE:
Before replacing the system board, replace the old iDRAC MAC address label in the Information tag with the
iDRAC MAC address label of the replacement system board.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If you are replacing the system board, remove all the components that are listed in the
removing the system board
section.
Steps
1.
Unpack the new system board assembly.
NOTE:
Do not lift the system board by holding a memory module, processor, or other components.
CAUTION:
Take care not to damage the system identification button while placing the system board into the chassis.
2.
Holding the system board holder, lower the system board it into the system.
3.
Incline the system board at an angle and align the connectors with the slots on the rear of the chassis.
4.
Slide the system board towards the rear of the chassis until the connectors are firmly seated in the slots.
Figure 76. Installing the system board
5.
Using a Phillips #2 screwdriver, fasten the screws that secure the system board to the chassis.
Next steps
1.
Replace the following:
a.
Trusted platform module
NOTE:
The TPM Module must be replaced only while installing new system board.
b.
Internal dual SD module
, if applicable
c.
Heat sink and processor
d.
If applicable,
Storage controller card
Installing and removing system components
91