Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 70

Installing the optional optical drive

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Figure 49. Removing the optical drive Next steps 1. Replace the optical drive or install an optical drive blank. NOTE: Blanks must be installed on empty optical drive slot to maintain FCC certification of the system. The blank also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. Installing the optional optical drive The procedure for installing an optical drive and optical drive blank. Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. If installed, remove the optical drive blank by pressing the blue release tab at the back of the blank and pushing the blank out of the system. NOTE: Route the cable properly when you replace it to prevent the cable from being pinched or crimped. Steps 1. Insert the optical drive until the blue release tab locks in the slot on the chassis. 2. Connect the power and data cable to the appropriate ports on the optical drive. NOTE: Route the cable properly to prevent the cable from being pinched or crimped. 3. Connect the power and data cables to the connectors on the system board. 70 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Figure 49. Removing the optical drive
Next steps
1.
Replace the optical drive or install an optical drive blank
.
NOTE:
Blanks must be installed on empty optical drive slot to maintain FCC certification of the system. The blank
also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system.
Installing the optional optical drive
The procedure for installing an optical drive and optical drive blank.
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
If installed, remove the optical drive blank by pressing the blue release tab at the back of the blank and pushing the blank out of the
system.
NOTE:
Route the cable properly when you replace it to prevent the cable from being pinched or crimped.
Steps
1.
Insert the optical drive until the blue release tab locks in the slot on the chassis.
2.
Connect the power and data cable to the appropriate ports on the optical drive.
NOTE:
Route the cable properly to prevent the cable from being pinched or crimped.
3.
Connect the power and data cables to the connectors on the system board.
70
Installing and removing system components