Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 69

Optional internal USB memory key, Replacing the optional internal USB memory key

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Next steps 1. Follow the procedure listed in After working inside your system. 2. Confirm that the battery is operating properly, by performing the following steps: a. Enter the System Setup, while booting, by pressing F2. b. Enter the correct time and date in the System Setup Time and Date fields. c. Exit the System Setup. d. To test the newly installed battery, remove the system from the enclosure for at least an hour. e. Reinstall the system into the enclosure after an hour. f. Enter the System Setup and if the time and date are still incorrect, see Getting help section. Optional internal USB memory key NOTE: To locate the internal USB port on the system board, see the System board jumpers and connectors section. Replacing the optional internal USB memory key Prerequisites CAUTION: To avoid interference with other components in the server, the maximum permissible dimensions of the USB memory key: 15.9 mm width x 57.15 mm length x 7.9 mm height. 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the expansion card riser. Steps 1. Locate the USB port or USB memory key on the system board. To locate the USB port, see the System board jumpers and connectors section. 2. If installed, remove the USB memory key from the USB port. 3. Insert the replacement USB memory key into the USB port. Next steps 1. Replace the expansion card riser. 2. Follow the procedure that is listed in After working inside your system. 3. While booting, press F2 to enter System Setup and verify that the system detects the USB memory key. Optional optical drive Removing the optical drive The procedure for removing an optical drive and optical drive blank is the same. Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. NOTE: Observe the routing of the cable as you remove it from the system. Steps 1. Disconnect the power and signal cables from the optical drive. 2. To release the optical drive, press the release tab and push the drive towards the front of the system. 3. Slide the optical drive out of the system. Installing and removing system components 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Next steps
1.
Follow the procedure listed in
After working inside your system
.
2.
Confirm that the battery is operating properly, by performing the following steps:
a.
Enter the System Setup, while booting, by pressing
F2
.
b.
Enter the correct time and date in the System Setup
Time
and
Date
fields.
c.
Exit
the System Setup.
d.
To test the newly installed battery, remove the system from the enclosure for at least an hour.
e.
Reinstall the system into the enclosure after an hour.
f.
Enter the System Setup and if the time and date are still incorrect, see
Getting help
section.
Optional internal USB memory key
NOTE:
To locate the internal USB port on the system board, see the
System board jumpers and connectors
section.
Replacing the optional internal USB memory key
Prerequisites
CAUTION:
To avoid interference with other components in the server, the maximum permissible dimensions of the USB
memory key: 15.9 mm width x 57.15 mm length x 7.9 mm height.
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the expansion card riser
.
Steps
1.
Locate the USB port or USB memory key on the system board.
To locate the USB port, see the
System board jumpers and connectors
section.
2.
If installed, remove the USB memory key from the USB port.
3.
Insert the replacement USB memory key into the USB port.
Next steps
1.
Replace the expansion card riser
.
2.
Follow the procedure that is listed in
After working inside your system
.
3.
While booting, press F2 to enter System Setup and verify that the system detects the USB memory key.
Optional optical drive
Removing the optical drive
The procedure for removing an optical drive and optical drive blank is the same.
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
NOTE:
Observe the routing of the cable as you remove it from the system.
Steps
1.
Disconnect the power and signal cables from the optical drive.
2.
To release the optical drive, press the release tab and push the drive towards the front of the system.
3.
Slide the optical drive out of the system.
Installing and removing system components
69