Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 75

Optional IDSDM or vFlash module, Removing the optional IDSDM or vFlash card

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Figure 55. Installing the heat sink Next steps 1. Install the air shroud. 2. Follow the procedure listed in the After working inside your system. Optional IDSDM or vFlash module The IDSDM or vFlash module combines the IDSDM and/or vFlash features into a single module. NOTE: The write-protect switch is on the IDSDM or vFlash module. Removing the optional IDSDM or vFlash card Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud. 4. If you are replacing the IDSDM/vFlash card, remove the MicroSD cards. NOTE: Temporarily label each SD card with its corresponding slot number before removal. Reinstall the SD cards into the corresponding slots. Steps Holding the pull tab, lift the IDSDM/vFlash card out of the system. Next steps NOTE: If you are replacing the IDSDM or vFlash module, remove the MicroSD cards. 1. Replace the IDSDM/vFlash module. Installing optional IDSDM or vFlash card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. Installing and removing system components 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Figure 55. Installing the heat sink
Next steps
1.
Install the air shroud
.
2.
Follow the procedure listed in the
After working inside your system
.
Optional IDSDM or vFlash module
The IDSDM or vFlash module combines the IDSDM and/or vFlash features into a single module.
NOTE:
The write-protect switch is on the IDSDM or vFlash module.
Removing the optional IDSDM or vFlash card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud.
4.
If you are replacing the IDSDM/vFlash card,
remove the MicroSD cards
.
NOTE:
Temporarily label each SD card with its corresponding slot number before removal. Reinstall the SD cards
into the corresponding slots.
Steps
Holding the pull tab, lift the IDSDM/vFlash card out of the system.
Next steps
NOTE:
If you are replacing the IDSDM or vFlash module, remove the MicroSD cards.
1.
Replace the IDSDM/vFlash module.
Installing optional IDSDM or vFlash card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
Installing and removing system components
75