Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 53

Intrusion switch, Removing the intrusion switch

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Figure 30. Installing a 2.5-inch drive into the 3.5-inch drive adapter Next steps 1. Install the drive adapter into the drive carrier. 2. Install the drive carrier. 3. If removed, install the front bezel. Intrusion switch Removing the intrusion switch Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Keep the plastic scribe ready. Steps 1. Disconnect and remove the intrusion switch cable connector from connector on the system board. NOTE: Observe the routing of the cable as you remove it from the system. 2. Using a plastic scribe, slide the intrusion switch out of the intrusion switch slot. Installing and removing system components 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Figure 30. Installing a 2.5-inch drive into the 3.5-inch drive adapter
Next steps
1.
Install the drive adapter into the drive carrier
.
2.
Install the drive carrier
.
3.
If removed, install the front bezel
.
Intrusion switch
Removing the intrusion switch
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Keep the plastic scribe ready.
Steps
1.
Disconnect and remove the intrusion switch cable connector from connector on the system board.
NOTE:
Observe the routing of the cable as you remove it from the system.
2.
Using a plastic scribe, slide the intrusion switch out of the intrusion switch slot.
Installing and removing system components
53