Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 60

Removing the expansion card riser

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Table 11. Expansion card installation order(continued) Card description Card type Maximum allowed Slot Priority Slot width FC8 HBA HBA: FC8 1 2 x16 1 1 x8 BOSS2 card Internal 1 Storage 1 2 x16 1 x8 1G Network NIC: 1Gb 1 card 1 2 x16 1 x4 1 1 x8 Link width x8 x4 x8 x4 x8 x4 x4 Card width Card length SW HL SW HL SW HL SW HL SW HL SW HL SW HL Card height FH LP FH LP FH LP LP Removing the expansion card riser Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. Steps 1. Open the blue expansion card riser retention-latch located on the system. 2. Holding the blue touch points, lift the expansion card riser from the system. Figure 37. Removing the expansion card riser 3. If you are not replacing the expansion card riser, install a expansion card riser filler bracket by performing the following steps: a. Align the expansion card riser filler bracket with the slot on the system. b. Push the expansion card riser filler bracket downward until firmly seated. c. Close the blue expansion card retention latch by pushing the latch down until the latch snaps into place. d. Using a Phillips #2 screwdriver, tighten the screw to secure the expansion card riser filler to the chassis. 4. Using a Phillips #2 screwdriver, fasten the screw to secure the expansion card riser filler to the chassis. 60 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Table 11. Expansion card installation order(continued)
Card
description
Card type
Maximum
allowed
Slot
Priority
Slot width
Link width
Card width
Card length
Card height
FC8 HBA
HBA: FC8
1
2
x16
x8
SW
HL
FH
1
1
x8
x4
SW
HL
LP
BOSS2 card
Internal
Storage
1
2
x16
x8
SW
HL
FH
1
1
x8
x4
SW
HL
LP
1G Network
card
NIC: 1Gb
1
2
x16
x8
SW
HL
FH
1
1
x4
x4
SW
HL
LP
1
1
x8
x4
SW
HL
LP
Removing the expansion card riser
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud
.
Steps
1.
Open the blue expansion card riser retention-latch located on the system.
2.
Holding the blue touch points, lift the expansion card riser from the system.
Figure 37. Removing the expansion card riser
3.
If you are not replacing the expansion card riser, install a expansion card riser filler bracket by performing the following steps:
a.
Align the expansion card riser filler bracket with the slot on the system.
b.
Push the expansion card riser filler bracket downward until firmly seated.
c.
Close the blue expansion card retention latch by pushing the latch down until the latch snaps into place.
d.
Using a Phillips #2 screwdriver, tighten the screw to secure the expansion card riser filler to the chassis.
4.
Using a Phillips #2 screwdriver, fasten the screw to secure the expansion card riser filler to the chassis.
60
Installing and removing system components