Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 54

Installing the intrusion switch

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Figure 31. Removing the intrusion switch Next steps 1. Replace the intrusion switch. Installing the intrusion switch Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. Steps 1. Align and insert the intrusion switch in the slot until it is firmly seated in the slot on the chassis. NOTE: Route the cable properly when you replace it to prevent the cable from being pinched or crimped. 2. Connect the intrusion switch cable to the connector on the system board. Figure 32. Installing the intrusion switch Next steps 1. Follow the procedure listed in After working inside your system. 54 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Figure 31. Removing the intrusion switch
Next steps
1.
Replace the intrusion switch
.
Installing the intrusion switch
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
Steps
1.
Align and insert the intrusion switch in the slot until it is firmly seated in the slot on the chassis.
NOTE:
Route the cable properly when you replace it to prevent the cable from being pinched or crimped.
2.
Connect the intrusion switch cable to the connector on the system board.
Figure 32. Installing the intrusion switch
Next steps
1.
Follow the procedure listed in
After working inside your system
.
54
Installing and removing system components