Dell PowerEdge R340 EMC PowerEdge R340 Installation and Service Manual - Page 50

Installing the drive into the drive carrier

Get Dell PowerEdge R340 PDF manuals and user guides View all Dell PowerEdge R340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Figure 27. Removing the drive from the drive carrier Next steps 1. Install the drive into the drive carrier. Installing the drive into the drive carrier Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. If installed, remove the front bezel. 3. Remove the drive blank. Steps 1. Insert the drive into the drive carrier with the drive connector facing towards the rear of the carrier. 2. Align the screw holes on the drive with the screws holes on the drive carrier. 3. Using a Phillips #1 screwdriver, replace the screws to secure the drive to the drive carrier. NOTE: When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-pounds. NOTE: Use the screws shipped with the drive carrier to secure the drive to the drive carrier. 50 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Figure 27. Removing the drive from the drive carrier
Next steps
1.
Install the drive into the drive carrier
.
Installing the drive into the drive carrier
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
If installed,
remove the front bezel
.
3.
Remove the drive blank
.
Steps
1.
Insert the drive into the drive carrier with the drive connector facing towards the rear of the carrier.
2.
Align the screw holes on the drive with the screws holes on the drive carrier.
3.
Using a Phillips #1 screwdriver, replace the screws to secure the drive to the drive carrier.
NOTE:
When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-pounds.
NOTE:
Use the screws shipped with the drive carrier to secure the drive to the drive carrier.
50
Installing and removing system components