Dell PowerEdge R940 EMC Installation and Service Manual - Page 118

Installing the PEM

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Figure 68. Removing the PEM Next steps Install the PEM. Installing the PEM Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. Steps 1. Hold the PEM using the handle and align the slots on the sides of the PEM with the standoffs on the sides of the system. 2. Lower the PEM until it clicks into place. 3. Re-connect the cables to the PEM. For information about cable routing, see the section UPI cable routing on page 120. 4. Hold the PEM handle and lower the PEM until it firmly seats in place. 118 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Figure 68. Removing the PEM
Next steps
Install the PEM
.
Installing the PEM
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
Steps
1.
Hold the PEM using the handle and align the slots on the sides of the PEM with the standoffs on the sides of the system.
2.
Lower the PEM until it clicks into place.
3.
Re-connect the cables to the PEM. For information about cable routing, see the section
UPI cable routing
on page 120.
4.
Hold the PEM handle and lower the PEM until it firmly seats in place.
118
Installing and removing system components