Dell PowerEdge R940 EMC Installation and Service Manual - Page 159

Installing the right control panel

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 159 highlights

NOTE: Ensure that you note the routing of the cables as you remove them from the system board. You must route the cables properly when you replace them to prevent the cables from being pinched or crimped. 7. Press the blue release tabs on the fan tray and lower the sides of the tray. Steps 1. Press the cable management bracket until the tabs on the bracket disengage from the slots on the right side of the system and lift the cable management bracket from the system. 2. Holding the pull tab, disconnect the control panel cable from the system board. 3. Using a Torx #T30 screwdriver, remove the screws that connect the control panel to the system. 4. Holding the control panel by its sides, remove the control panel away from the system. Figure 106. Removing the right control panel Next steps Install the right control panel. Installing the right control panel Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. Steps 1. Route the cables through the cable routing hooks on the side of the system. 2. Lower the cable management bracket into the system. 3. Press the bracket and insert the tabs on the bracket into the slots on the right side of the system. Installing and removing system components 159

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. You must route
the cables properly when you replace them to prevent the cables from being pinched or crimped.
7.
Press the blue release tabs on the fan tray and lower the sides of the tray.
Steps
1.
Press the cable management bracket until the tabs on the bracket disengage from the slots on the right side of the system and lift the
cable management bracket from the system.
2.
Holding the pull tab, disconnect the control panel cable from the system board.
3.
Using a Torx #T30 screwdriver, remove the screws that connect the control panel to the system.
4.
Holding the control panel by its sides, remove the control panel away from the system.
Figure 106. Removing the right control panel
Next steps
Install the right control panel
.
Installing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
Steps
1.
Route the cables through the cable routing hooks on the side of the system.
2.
Lower the cable management bracket into the system.
3.
Press the bracket and insert the tabs on the bracket into the slots on the right side of the system.
Installing and removing system components
159