Dell PowerEdge R940 EMC Installation and Service Manual - Page 130

Removing the expansion card from expansion card riser

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 130 highlights

Figure 79. Installing expansion card riser (left) Next steps 1. Connect the cables to the expansion card. 2. Follow the procedure listed in After working inside your system on page 66. Removing the expansion card from expansion card riser Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. 3. Disconnect the cables from the expansion card. 4. Remove the expansion card riser. Steps 1. Press the black tab on the expansion card riser and slide the PCIe retention bracket up. NOTE: This step is applicable only if you are removing the expansion cards from the slots 12 and 13 of Riser 3 (IO_RISER3) and slots 9 and 10 of Riser 2 (IO_RISER2). 2. Lift the PCIe card latch. 3. Hold the expansion card by its edges, and lift the card out until the connector on the card disconnects from the connector on the riser. 130 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Figure 79. Installing expansion card riser (left)
Next steps
1.
Connect the cables to the expansion card.
2.
Follow the procedure listed in
After working inside your system
on page 66.
Removing the expansion card from expansion card riser
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
3.
Disconnect the cables from the expansion card.
4.
Remove the expansion card riser
.
Steps
1.
Press the black tab on the expansion card riser and slide the PCIe retention bracket up.
NOTE:
This step is applicable only if you are removing the expansion cards from the slots 12 and 13 of Riser 3
(IO_RISER3) and slots 9 and 10 of Riser 2 (IO_RISER2).
2.
Lift the PCIe card latch.
3.
Hold the expansion card by its edges, and lift the card out until the connector on the card disconnects from the connector on the riser.
130
Installing and removing system components