Dell PowerEdge R940 EMC Installation and Service Manual - Page 80

Removing the fan tray

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Figure 34. Installing the fan cage Next steps 1. Follow the procedure listed in After working inside your system on page 66. Removing the fan tray Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. 3. Remove the air shroud. 4. Remove the fan cage. 5. If installed, remove the expansion card risers. 6. If applicable, lift the PEM by using the PEM handle until the PEM is in an upright position. 7. Release the backplane and fan power cables from the cable clips on the fan tray and disconnect the power cables from the connectors on the system board. Steps 1. Press the blue release tabs on the side of the fan tray to unlock the tray. 2. Holding the fan tray lift the tray out of the system. 80 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Figure 34. Installing the fan cage
Next steps
1.
Follow the procedure listed in
After working inside your system
on page 66.
Removing the fan tray
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
3.
Remove the air shroud
.
4.
Remove the fan cage
.
5.
If installed,
remove the expansion card risers
.
6.
If applicable, lift the PEM by using the PEM handle until the PEM is in an upright position.
7.
Release the backplane and fan power cables from the cable clips on the fan tray and disconnect the power cables from the
connectors on the system board.
Steps
1.
Press the blue release tabs on the side of the fan tray to unlock the tray.
2.
Holding the fan tray lift the tray out of the system.
80
Installing and removing system components