Dell PowerEdge R940 EMC Installation and Service Manual - Page 135

Installing the NDC riser

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

Figure 84. Removing the NDC riser Next steps 1. Install the NDC riser. Installing the NDC riser Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. Steps 1. Hold the Network Daughter Card (NDC) riser by its edges and align the connector on the NDC riser and guide pin on the system board. 2. Insert the NDC riser until the card is fully seated. 3. Close the riser retention bracket and slide the bracket to lock the NDC riser. Installing and removing system components 135

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Figure 84. Removing the NDC riser
Next steps
1.
Install the NDC riser
.
Installing the NDC riser
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
Steps
1.
Hold the Network Daughter Card (NDC) riser by its edges and align the connector on the NDC riser and guide pin on the system
board.
2.
Insert the NDC riser until the card is fully seated.
3.
Close the riser retention bracket and slide the bracket to lock the NDC riser.
Installing and removing system components
135