Dell PowerEdge R940 EMC Installation and Service Manual - Page 134

Network daughter card riser, Removing the NDC riser

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

Figure 83. Installing the M.2 SSD module Next steps 1. Install the BOSS card. NOTE: Installing the BOSS card is similar to installing the expansion card riser. 2. Install the air shroud. 3. Follow the procedure listed in After working inside your system on page 66. Network daughter card riser Removing the NDC riser Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. 3. Disconnect the cables connected to the Network Daughter Card (NDC) riser. Steps 1. Slide the riser retention bracket to unlock the NDC riser. 2. Hold the NDC riser by its edges, and pull the NDC riser until the card edge connector disengages from the connector on the system board. 3. Lift the NDC riser from the system. 134 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Figure 83. Installing the M.2 SSD module
Next steps
1.
Install the BOSS card.
NOTE:
Installing the BOSS card is similar to
installing the expansion card riser
.
2.
Install the air shroud
.
3.
Follow the procedure listed in
After working inside your system
on page 66.
Network daughter card riser
Removing the NDC riser
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
3.
Disconnect the cables connected to the Network Daughter Card (NDC) riser.
Steps
1.
Slide the riser retention bracket to unlock the NDC riser.
2.
Hold the NDC riser by its edges, and pull the NDC riser until the card edge connector disengages from the connector on the system
board.
3.
Lift the NDC riser from the system.
134
Installing and removing system components